- 您現在的位置：買賣IC網 > PDF目錄374721 > SC2434SWTRT (Semtech Corporation) TriPhase Current Mode Controller with Power Good PDF資料下載
參數資料
| 型號： | SC2434SWTRT |
| 廠商： | Semtech Corporation |
| 英文描述： | TriPhase Current Mode Controller with Power Good |
| 中文描述： | 三相電流模式控制器與電源良好 |
| 文件頁數： | 8/19頁 |
| 文件大?。?/td> | 302K |
| 代理商： | SC2434SWTRT |
8
2005 Semtech Corp.
www.semtech.com
PRELIMINARY
POWER MANAGEMENT
Applications Information (Cont.)
SC2434
Program The Controller
Please refer to Fig. 1 and the application schematics in
this data sheet for the discussion. The resistor from pin
10 to ground, R
, programs the switching frequency. The
resistor from pin 11 to ground, R
DAC
, sets the DAC current
step size. The resistors, R
, R
, and R
set the DAC
step size, the output voltage set point, and the droop,
respectively.
MathCAD programs are available to calculate the required
parameters upon request.
Programming The Switching Frequency
The oscillator frequency can be selected first by setting the
value of R
OSC
as given below:
ROSC
28.5 K
750 KHz
Fosc
.
IDAC_LSB
1
16
Vbg
RDAC
.
RFB
VIDstep
IDAC_LSB
The per phase switching frequency is 1/3 of the oscilla-
tor frequency in three-phase mode. It is recommended
that per phase switching frequency is 200~300KHz for
good trade off of efficiency vs. transient responses.
Programming The DAC Step Size
The SC2434 allows programming of the output voltage
and the DAC step size by selecting external resistors. The
LSB of the DAC current is given by:
where V
bg
is the trimmed voltage reference (V
= 1.5V)
and R
is the resistor from pin 11 to ground. For the
given VID step size (25mV for VRM9.0 and VRM9.2 speci-
fications), the feedback resistor can be calculated accord-
ing to the LSB of DAC current:
The above two equations are for choosing R
and R
simultaneously. The advantage of this method is that new
VID step size can be accommodated by modifying external
components while maintaining the required precision.
Choose Current Sensing Resistor According To The
Threshold Of OCP
The SC2434 controller has an over current protection (OCP)
threshold of 120mV. The normal practice is to let the
peak voltage across the sensing resistor corresponding to
full-load operation be 75% of the given OCP threshold:
Rdrp
RFBRsense
Vout
Gca
.
Iout
Nphase
.
where I
is the peak current of the output inductor. Since
the choice of sensing resistor values are limited, typically 3
mOhm, 4 mOhm, or 5 mOhm, it is recommended to choose
the sensing resistor with a bigger value than that was cal-
culated, and to use a resistive divider to get the equiva-
lent R
value. The two attenuation resistors should
have value of 20 Ohm in parallel. A filter capacitor of
10nF is also needed to be across the OC+ and OC- pins of
the controller IC. Please refer the application circuit sche-
matic.
Programming The Dynamic (Active) Droop
To optimize transient responses, the SC2434 actively regu-
lates output voltage as a function of output current. At
zero current the output is positioned to the upper limit of
the regulation window. As the load increases, the output
“droops” towards the lower limit. This makes optimum
use of the output voltage error band, yielding minimum
output capacitor size and cost.
The droop is adjusted by setting the DC gain of the error
amplifier. This is done by choosing the resistor from the
ERROUT pin to the FB pin (R
) of the controller. While
the optimum value of R
may be derived experimentally,
the following equation can provide the first order calcula-
tion for given droop slope:
where R
is the current sensing resistance after taken
into account of attenuation, and G
is the gain of the
current amplifier while N
phase
is number of phases being
used.
Any output interconnection impedance not within the feed-
back loop can contribute to additional drooping. This ef-
fect has to be taken into account. Usually, when testing
the regulation at different CPU pins, the results may vary
slightly by same token.
It is important to use surface mount current sensing resis-
tor to minimize the parasitic inductance for accurate cor-
relation between the above equation and the test results.
This is because the inductive contribution, which may also
R
sense
75%
"
120mV
I
peak
相關PDF資料 |
PDF描述 |
|---|---|
| SC2434TSTR | TriPhase Current Mode Controller with Power Good |
| SC2434TSTRT | TriPhase Current Mode Controller with Power Good |
| SC2440 | 2.5 MHz Dual Switching Regulator with Integrated 2A Switches |
| SC2440EVB | 2.5 MHz Dual Switching Regulator with Integrated 2A Switches |
| SC2440TETRT | 2.5 MHz Dual Switching Regulator with Integrated 2A Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC2434TSTR | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:TriPhase Current Mode Controller with Power Good |
| SC2434TSTRT | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:TriPhase Current Mode Controller with Power Good |
| SC24-391-R | 功能描述:INDUCTOR SHIELD 390UH 60MA SMD RoHS:是 類別:電感器，線圈，扼流圈 >> 固定式 系列:SC24 標準包裝:500 系列:1331 電感:1.2µH 電流:247mA 電流 - 飽和:247mA 電流 - 溫升:- 類型:鐵芯體 容差:±10% 屏蔽:屏蔽 DC 電阻(DCR):最大 730 毫歐 Q因子@頻率:40 @ 7.9MHz 頻率 - 自諧振:130MHz 材料 - 芯體:鐵 封裝/外殼:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安裝類型:表面貼裝 包裝:帶卷 (TR) 工作溫度:-55°C ~ 105°C 頻率 - 測試:7.9MHz |
| SC2440 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:2.5 MHz Dual Switching Regulator with Integrated 2A Switches |
| SC2440EVB | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:2.5 MHz Dual Switching Regulator with Integrated 2A Switches |
發布緊急采購，3分鐘左右您將得到回復。