- 您現在的位置：買賣IC網 > PDF目錄374721 > SC2434SWTRT (Semtech Corporation) TriPhase Current Mode Controller with Power Good PDF資料下載
參數資料
| 型號： | SC2434SWTRT |
| 廠商： | Semtech Corporation |
| 英文描述： | TriPhase Current Mode Controller with Power Good |
| 中文描述： | 三相電流模式控制器與電源良好 |
| 文件頁數： | 11/19頁 |
| 文件大?。?/td> | 302K |
| 代理商： | SC2434SWTRT |
11
2005 Semtech Corp.
www.semtech.com
POWER MANAGEMENT
Applications Information (Cont.)
SC2434
PCB Layout Consideration
Good layout is necessary for successful implementation of the SC2434 based 3 tri-phase topology. There are few
general rules:
·
Reserve enough PCB space for the power supply (1.2~1.5 square inch for every 10A of load current);
·
Place enough high frequency ceramic capacitors inside and around the CPU socket (please follow CPU manufacture’s
decoupling guideline);
·
Place bulk output capacitors around the CPU socket as uniformly as possible. The connection copper between
these capacitors and the CPU socket must be short and wide to minimize inductance and resistance;
·
Always place the high power parts first;
·
Always use a ground plane or ground planes;
·
Always try to minimize the stray inductance of the high pulsating current loop which is formed by input capacitors
and the MOSFET half-bridges.
The following layout guideline gives details on how to achieve a good layout:
·
Input filter should contain mixed electrolytic capacitors and MLC capacitors. For every 20A of load current, use
about 10uF of MLC caps. Put MLC caps close to current sensing resistor;
·
Use surface mount current sensing resistor (typically 3~5 mOhm in surface mount package with low temperature
coefficient and low package inductance, typically less than 0.3nH);
·
Try to minimize the stray inductance from the current sensing resistor to the drains of the top FETs by using wide
trace (>0.5” wide and no more than 3” long). This trace can run on inner1 layer, for example, if the inner2 layer is
the ground plane, assuming the FETs are on the top layer. This arrangement forms so called strip line structure for
the pulsating power current, which yields least amount of stray inductance. The concept is depicted in Fig. 7;
·
Keep the layout as electrically symmetrical as possible, as shown in Fig. 8, to avoid very uneven stray inductance
from the sensing resistor to the drains of the top FETs;
·
Use a pair of closely paralleled traces to pick up the sensing voltage across the sensing resistor. The sensing traces
server as differential input to the OC+ and OC- pins of the SC2434 controller. These traces should run on a routing
layer (e.g., bottom layer for 4 layer PCB case) to avoid picking up strong AC magnetic field due to power current flow.
In this case, the differential sensing traces are shielded by the ground layer. The filter cap across the OC+ and OC-
pins should be placed as close as possible to the controller. Pay close attention that never allow power current
flowing on or running close by the sensing traces. Please see Fig. 8;
·
Separate power ground from analog ground to prevent power current from running over the analog ground plane.
The SC2434 controller should be placed on the quite analog ground area. The analog ground should be single-
point connected to the PGND near the output capacitor or the CPU socket to provide best possible ground sense.
Refer to the application schematics for those components should be connected directly to the AGND (Vcc decoupling
caps, cap on BGOUT pin, resistors on OSCREF pin, DACREF pin, FB pin, and PGIN pin).
Fig. 7 - Use MLC capacitors and strip line structure to minimize the stray inductance for the switching current loop.
TOP FET
BOT FET
D
S
D
S
MLC
VIA
VIA
Rsense
Ground Plane
相關PDF資料 |
PDF描述 |
|---|---|
| SC2434TSTR | TriPhase Current Mode Controller with Power Good |
| SC2434TSTRT | TriPhase Current Mode Controller with Power Good |
| SC2440 | 2.5 MHz Dual Switching Regulator with Integrated 2A Switches |
| SC2440EVB | 2.5 MHz Dual Switching Regulator with Integrated 2A Switches |
| SC2440TETRT | 2.5 MHz Dual Switching Regulator with Integrated 2A Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC2434TSTR | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:TriPhase Current Mode Controller with Power Good |
| SC2434TSTRT | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:TriPhase Current Mode Controller with Power Good |
| SC24-391-R | 功能描述:INDUCTOR SHIELD 390UH 60MA SMD RoHS:是 類別:電感器，線圈，扼流圈 >> 固定式 系列:SC24 標準包裝:500 系列:1331 電感:1.2µH 電流:247mA 電流 - 飽和:247mA 電流 - 溫升:- 類型:鐵芯體 容差:±10% 屏蔽:屏蔽 DC 電阻(DCR):最大 730 毫歐 Q因子@頻率:40 @ 7.9MHz 頻率 - 自諧振:130MHz 材料 - 芯體:鐵 封裝/外殼:0.312" L x 0.115" W x 0.135" H（7.94mm x 2.92mm x 3.43mm） 安裝類型:表面貼裝 包裝:帶卷 (TR) 工作溫度:-55°C ~ 105°C 頻率 - 測試:7.9MHz |
| SC2440 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:2.5 MHz Dual Switching Regulator with Integrated 2A Switches |
| SC2440EVB | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:2.5 MHz Dual Switching Regulator with Integrated 2A Switches |
發布緊急采購，3分鐘左右您將得到回復。