參數資料
型號: SC16IS760IBS
廠商: NXP Semiconductors N.V.
元件分類: 連接器件
英文描述: Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
封裝: SC16IS740IPW/Q900<SOT403-1 (TSSOP16)|<<http://www.nxp.com/packages/SOT403-1.html<1<Always Pb-free,;SC16IS740IPW<SOT403-1 (TSSOP16)|<<http://www.nxp.com/packages/SOT403-1.
文件頁數: 42/62頁
文件大?。?/td> 308K
代理商: SC16IS760IBS
SC16IS740_750_760_6
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 06 — 13 May 2008
42 of 62
NXP Semiconductors
SC16IS740/750/760
Single UART with I
2
C-bus/SPI interface, 64-byte FIFOs, IrDA SIR
Table 33
and
Table 34
show the bits’ presentation at the subaddress byte for I
2
C-bus and
SPI interfaces. Bit 0 is not used, bits 2:1 select the channel, bits 6:3 select one of the
UART internal registers. Bit 7 is not used with the I
2
C-bus interface, but it is used by the
SPI interface to indicate a read or a write operation.
The register read cycle (see
Figure 23
) commences in a similar manner, with the master
sending a slave address with the direction bit set to ‘write’ with a following subaddress.
Then, in order to reverse the direction of the transfer, the master issues a repeated START
followed again by the device address, but this time with the direction bit set to ‘read’. The
data bytes starting at the internal subaddress will be clocked out of the device, each
followed by a master-generated acknowledge. The last byte of the read cycle will be
followed by a negative acknowledge, signalling the end of transfer. The cycle is terminated
by a STOP signal.
White block: host to SC16IS740/750/760
Grey block: SC16IS740/750/760 to host
(1) See
Table 33
for additional information.
Fig 22. Master writes to slave
S
SLAVE ADDRESS
002aab047
W
A
REGISTER ADDRESS
(1)
A
nDATA
A
P
White block: host to SC16IS740/750/760
Grey block: SC16IS740/750/760 to host
(1) See
Table 33
for additional information.
Fig 23. Master read from slave
S
SLAVE ADDRESS
002aab048
W
A
REGISTER ADDRESS
(1)
A
NA
P
S
SLAVE ADDRESS
R
A
nDATA
A
LAST DATA
Table 33.
Bit
7
6:3
2:1
Register address byte (I
2
C)
Name
-
A[3:0]
CH1, CH0
Function
not used
UART’s internal register select
channel select: CH1 = 0, CH0 = 0
Other values are reserved and should not be used.
not used
0
-
相關PDF資料
PDF描述
SC16IS760IPW Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS741IPW Single UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS752IBS Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS752IPW Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
SC16IS762IBS Dual UART with I2C-bus-SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
相關代理商/技術參數
參數描述
SC16IS760IBS,128 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16IS760IBS,151 功能描述:UART 接口集成電路 UART I2C/SPI RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16IS760IBS,157 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16IS760IBS-F 功能描述:UART 接口集成電路 I2C/SPI-UARTBRIDGE W/IRDA AND GPIO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16IS760IPW 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support