參數資料
型號： SC16C650BIBS
廠商： NXP Semiconductors N.V.
元件分類： 收發器
英文描述： 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder
封裝： SC16C650BIB48<SOT313-2 (LQFP48)|<<http://www.nxp.com/packages/SOT313-2.html<1<Always Pb-free,;SC16C650BIB48<SOT313-2 (LQFP48)|<<http://www.nxp.com/packages/SOT313-2.html&
文件頁數： 27/48頁
文件大小： 241K
代理商： SC16C650BIBS
SC16C650B_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 14 September 2009
27 of 48
NXP Semiconductors
SC16C650B
UART with 32-byte FIFOs and IrDA encoder/decoder
7.9 Scratchpad Register (SPR)
The SC16C650B provides a temporary data register to store 8 bits of user information.
7.10 Enhanced Feature Register (EFR)
Enhanced features are enabled or disabled using this register.
Bits 0 through 4 provide single or dual character software flow control selection. When the
Xon1 and Xon2 and/or Xoff1 and Xoff2 modes are selected, the double 8-bit words are
concatenated into two sequential numbers.
Table 22.
Bit
7
Enhanced Feature Register bits description
Symbol
Description
EFR[7]
Automatic CTS flow control.
logic 0 = Automatic CTS flow control is disabled (normal default condition)
logic 1 = enable Automatic CTS flow control. Transmission will stop when
CTS goes to a logic 1. Transmission will resume when the CTS pin returns to
a logic 0.
EFR[6]
Automatic RTS flow control. Automatic RTS may be used for hardware flow
control by enabling EFR[6]. When Auto-RTS is selected, an interrupt will be
generated when the receive FIFO is filled to the programmed trigger level and
RTS will go to a logic 1 at the next trigger level. RTS will return to a logic 0 when
data is unloaded below the next lower trigger level (programmed trigger level 1).
The state of this register bit changes with the status of the hardware flow
control. RTS functions normally when hardware flow control is disabled.
0 = Automatic RTS flow control is disabled (normal default condition)
1 = enable Automatic RTS flow control
EFR[5]
Special Character Detect.
logic 0 = special character detect disabled (normal default condition)
logic 1 = special character detect enabled. The SC16C650B compares each
incoming receive character with Xoff2 data. If a match exists, the received
data will be transferred to FIFO and ISR[4] will be set to indicate detection of
special character. Bit 0 in the X-registers corresponds with the LSB bit for the
receive character. When this feature is enabled, the normal software flow
control must be disabled (EFR[3:0] must be set to a logic 0).
EFR[4]
Enhanced function control bit. The content of IER[7:4], ISR[5:4], FCR[5:4], and
MCR[7:5] can be modified and latched. After modifying any bits in the
enhanced registers, EFR[4] can be set to a logic 0 to latch the new values. This
feature prevents existing software from altering or overwriting the SC16C650B
enhanced functions.
logic 0 = disable (normal default condition)
logic 1 = enable
EFR[3:0]
Cont-3:0 Tx, Rx control. Logic 0 or cleared is the default condition.
Combinations of software flow control can be selected by programming these
bits. See
Table 23
.
6
5
4
3:0
相關PDF資料
PDF描述
SC16C652BIBS 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit-s (max.) with 32-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C654BIA68 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C654B 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
SC16C654BIB64 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C654BIBM 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder
相關代理商/技術參數
參數描述
SC16C650BIBS,128 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C650BIBS,151 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C650BIBS,157 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C650BIBS-F 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C650BIBS-S 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*