- 您現在的位置：買賣IC網 > PDF目錄379352 > SC16C650BIBS (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder PDF資料下載
參數資料
| 型號： | SC16C650BIBS |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 收發器 |
| 英文描述： | 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder |
| 封裝： | SC16C650BIB48<SOT313-2 (LQFP48)|<<http://www.nxp.com/packages/SOT313-2.html<1<Always Pb-free,;SC16C650BIB48<SOT313-2 (LQFP48)|<<http://www.nxp.com/packages/SOT313-2.html& |
| 文件頁數： | 19/48頁 |
| 文件大?。?/td> | 241K |
| 代理商： | SC16C650BIBS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
SC16C650B_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 14 September 2009
19 of 48
NXP Semiconductors
SC16C650B
UART with 32-byte FIFOs and IrDA encoder/decoder
7.3 FIFO Control Register (FCR)
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger
levels, and select the DMA mode.
7.3.1
DMA mode
7.3.1.1
Mode 0 (FCR bit 3 = 0)
Set and enable the interrupt for each single transmit or receive operation, and is similar to
the 16C450 mode. Transmit Ready (TXRDY) will go to a logic 0 whenever an empty
transmit space is available in the Transmit Holding Register (THR). Receive Ready
(RXRDY) will go to a logic 0 whenever the Receive Holding Register (RHR) is loaded with
a character.
7.3.1.2
Mode 1 (FCR bit 3 = 1)
Set and enable the interrupt in a block mode operation. The transmit interrupt is set when
the transmit FIFO is below the programmed trigger level. The receive interrupt is set when
the receive FIFO fills to the programmed trigger level. However, the FIFO continues to fill
regardless of the programmed level until the FIFO is full. RXRDY remains a logic 0 as long
as the FIFO fill level is above the programmed trigger level.
7.3.2
FIFO mode
Table 10.
Bit
7:6
FIFO Control Register bits description
Symbol
Description
FCR[7] (MSB),
FCR[6] (LSB)
FIFO interrupt.
An interrupt is generated when the number of characters in the FIFO
equals the programmed trigger level. However, the FIFO will continue to
be loaded until it is full. Refer to
Table 11
.
FCR[5] (MSB),
FCR[4] (LSB)
These bits are used to set the trigger level for the transmit FIFO
interrupt. The SC16C650B will issue a transmit empty interrupt when
the number of characters in FIFO drops below the selected trigger level.
Refer to
Table 12
.
FCR[3]
DMA mode select.
logic 0 = set DMA mode ‘0’ (normal default condition)
logic 1 = set DMA mode ‘1’
Transmit operation in mode ‘0’:
When the SC16C650B is in the
16C450 mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO mode
(FIFOs enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when there
are no characters in the transmit FIFO or transmit holding register, the
TXRDY pin will be a logic 0. Once active, the TXRDY pin will go to a
logic 1 after the first character is loaded into the transmit holding
register.
Receive operation in mode ‘0’:
When the SC16C650B is in 16C450
mode, or in the FIFO mode (FCR[0] = logic 1; FCR[3] = logic 0) and
there is at least one character in the receive FIFO, the RXRDY pin will
be a logic 0. Once active, the RXRDY pin will go to a logic 1 when there
are no more characters in the receiver.
RCVR trigger. These bits are used to set the trigger level for the receive
5:4
Logic 0 or cleared is the default condition; TX trigger level = 16.
3
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C652BIBS | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit-s (max.) with 32-byte FIFOs and infrared (IrDA) encoder-decoder |
| SC16C654BIA68 | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder |
| SC16C654B | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder |
| SC16C654BIB64 | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder |
| SC16C654BIBM | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.), with 64-byte FIFOs and infrared (IrDA) encoder-decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C650BIBS,128 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650BIBS,151 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650BIBS,157 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650BIBS-F | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650BIBS-S | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。