參數資料
型號： SC16C2550IB48,128
廠商： NXP Semiconductors
文件頁數： 45/46頁
文件大小： 0K
描述： IC DUART SOT313-2
標準包裝： 2,000
特點： 2 通道
通道數： 2，DUART
FIFO's： 16 字節
電源電壓： 2.5V，3.3V，5V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 管件
其它名稱： 935270020128
SC16C2550IB48-T
SC16C2550IB48-T-ND
Philips Semiconductors
SC16C2550
Dual UART with 16 bytes of transmit and receive FIFOs and IrDA
encoder/decoder
Product data
Rev. 03 — 19 June 2003
8 of 46
9397 750 11621
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
XTAL2
17
19
14
O
Output of the crystal oscillator or buffered clock. (See also XTAL1.)
Crystal oscillator output or buffered clock output. Should be left open if an
external clock is connected to XTAL1. For extended frequency operation,
this pin should be tied to VCC via a 2 k resistor.
CDA,
CDB
38, 19 42, 21
40, 16
I
Carrier Detect (Active-LOW). These inputs are associated with individual
UART channels A through B. A logic 0 on this pin indicates that a carrier
has been detected by the modem for that channel.
CTSA,
CTSB
36, 25 40, 28
38, 23
I
Clear to Send (Active-LOW). These inputs are associated with individual
UART channels, A through B. A logic 0 on the CTS pin indicates the
modem or data set is ready to accept transmit data from the SC16C2550.
Status can be tested by reading MSR[4]. This pin has no effect on the
UART’s transmit or receive operation.
DSRA,
DSRB
37, 22 41, 25
39, 20
I
Data Set Ready (Active-LOW). These inputs are associated with
individual UART channels, A through B. A logic 0 on this pin indicates the
modem or data set is powered-on and is ready for data exchange with the
UART. This pin has no effect on the UART’s transmit or receive operation.
DTRA,
DTRB
33, 34 37, 38
34, 35
O
Data Terminal REady (Active-LOW). These outputs are associated with
individual UART channels, A through B. A logic 0 on this pin indicates that
the SC16C2550 is powered-on and ready. This pin can be controlled via
the modem control register. Writing a logic 1 to MCR[0] will set the DTR
output to logic 0, enabling the modem. This pin will be a logic 1 after writing
a logic 0 to MCR[0], or after a reset. This pin has no effect on the UART’s
transmit or receive operation.
RIA, RIB
39, 23 43, 26
41, 21
I
Ring Indicator (Active-LOW). These inputs are associated with individual
UART channels, A through B. A logic 0 on this pin indicates the modem has
received a ringing signal from the telephone line. A logic 1 transition on this
input pin will generate an interrupt.
RTSA,
RTSB
32, 24 36, 27
33, 22
O
Request to Send (Active-LOW). These outputs are associated with
individual UART channels, A through B. A logic 0 on the RTS pin indicates
the transmitter has data ready and waiting to send. Writing a logic 1 in the
modem control register MCR[1] will set this pin to a logic 0, indicating data
is available. After a reset this pin will be set to a logic 1. This pin has no
effect on the UART’s transmit or receive operation.
RXA, RXB 10, 9
11, 10
5, 4
I
Receive data A, B. These inputs are associated with individual serial
channel data to the SC16C2550 receive input circuits, A-B. The RX signal
will be a logic 1 during reset, idle (no data), or when the transmitter is
disabled. During the local loop-back mode, the RX input pin is disabled and
TX data is connected to the UART RX input, internally.
TXA, TXB 11, 12 13, 14
7, 8
O
Transmit data A, B. These outputs are associated with individual serial
transmit channel data from the SC16C2550. The TX signal will be a logic 1
during reset, idle (no data), or when the transmitter is disabled. During the
local loop-back mode, the TX output pin is disabled and TX data is
internally connected to the UART RX input.
Table 2:
Pin description…continued
Symbol
Pin
Type Description
DIP40 PLCC44 LQFP48
相關PDF資料
PDF描述
SC16C2550IB48,157 IC DUART SOT313-2
SC16C2550IA44,518 IC DUART SOT187-2
SC16C2550IA44,512 IC DUART SOT187-2
VI-B7N-IX-F1 CONVERTER MOD DC/DC 18.5V 75W
SC16C2550BIN40,112 IC UART DUAL W/FIFO 40-DIP
相關代理商/技術參數
參數描述
SC16C2550IN40 制造商:PHILIP 功能描述:
SC16C2550IN40,112 功能描述:IC UART DUAL W/FIFO 40-DIP RoHS:是 類別:集成電路 (IC) >> 接口 - UART（通用異步接收器/發送器） 系列:- 標準包裝:250 系列:- 特點:* 通道數:2，DUART FIFO's:16 字節 規程:RS232，RS485 電源電壓:2.25 V ~ 5.5 V 帶并行端口:- 帶自動流量控制功能:是 帶IrDA 編碼器/解碼器:是 帶故障啟動位檢測功能:是 帶調制解調器控制功能:是 帶CMOS:是 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:托盤 其它名稱:XR16L2551IM-F-ND
SC16C2552 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual UART with 16-byte transmit and receive FIFOs
SC16C2552B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
SC16C2552BIA44 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*