- 您現在的位置：買賣IC網 > PDF目錄372121 > SC16C2550IA44 (NXP SEMICONDUCTORS) Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder PDF資料下載
參數資料
| 型號： | SC16C2550IA44 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder |
| 中文描述： | 2 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 封裝： | PLASTIC, MS-018, SOT-187-2, LCC-44 |
| 文件頁數： | 22/46頁 |
| 文件大?。?/td> | 603K |
| 代理商： | SC16C2550IA44 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
Philips Semiconductors
SC16C2550
Dual UART with 16 bytes of transmit and receive FIFOs and IrDA
encoder/decoder
Product data
Rev. 03 — 19 June 2003
22 of 46
9397 750 11621
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
7.5 Line Control Register (LCR)
The Line Control Register is used to specify the asynchronous data communication
format. The word length, the number of stop bits, and the parity are selected by
writing the appropriate bits in this register.
Table 12:
Bit
7-6
Interrupt Status Register bits description
Symbol
Description
ISR[7-6]
FIFOs enabled. These bits are set to a logic 0 when the FIFOs are
not being used in the 16C450 mode. They are set to a logic 1
when the FIFOs are enabled in the SC16C2550 mode.
Logic 0 or cleared = default condition.
ISR[5-4]
INT priority bits 4-3. These bits are enabled when EFR[4] is set to
a logic 1. ISR[4] indicates that matching Xoff character(s) have
been detected. ISR[5] indicates that CTS, RTS have been
generated. Note that once set to a logic 1, the ISR[4] bit will stay a
logic 1 until Xon character(s) are received.
Logic 0 or cleared = default condition.
ISR[3-1]
INT priority bits 2-0. These bits indicate the source for a pending
interrupt at interrupt priority levels 1, 2, and 3 (see
Table 11
).
Logic 0 or cleared = default condition.
ISR[0]
INT status.
Logic 0 = An interrupt is pending and the ISR contents may be
used as a pointer to the appropriate interrupt service routine.
Logic 1 = No interrupt pending (normal default condition).
5-4
3-1
0
Table 13:
Bit
7
Line Control Register bits description
Symbol
Description
LCR[7]
Divisor latch enable. The internal baud rate counter latch and
Enhance Feature mode enable.
Logic 0 = Divisor latch disabled (normal default condition).
Logic 1 = Divisor latch enabled.
LCR[6]
Set break. When enabled, the Break control bit causes a break
condition to be transmitted (the TX output is forced to a logic 0
state). This condition exists until disabled by setting LCR[6] to a
logic 0.
Logic 0 = no TX break condition (normal default condition)
Logic 1 = forces the transmitter output (TX) to a logic 0 for
alerting the remote receiver to a line break condition.
LCR[5-3]
Programs the parity conditions (see
Table 14
).
LCR[2]
Stop bits. The length of stop bit is specified by this bit in
conjunction with the programmed word length (see
Table 15
).
Logic 0 or cleared = default condition.
LCR[1-0]
Word length bits 1, 0. These two bits specify the word length to be
transmitted or received (see
Table 16
).
Logic 0 or cleared = default condition.
6
5-3
2
1-0
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C2550IN40 | Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder |
| SC16C2550 | Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder |
| SC16C2550IB48 | Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder-decoder |
| SC16C550B | 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs |
| SC16C550BIN40 | 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C2550IA44,512 | 功能描述:UART 接口集成電路 16C 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2550IA44,518 | 功能描述:UART 接口集成電路 16C 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2550IA44,529 | 功能描述:UART 接口集成電路 16C 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2550IB48 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder |
| SC16C2550IB48,128 | 功能描述:UART 接口集成電路 16C 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。