- 您現在的位置：買賣IC網 > PDF目錄374697 > SAB82525H (INFINEON TECHNOLOGIES AG) Data Communications ICs PDF資料下載
參數資料
| 型號： | SAB82525H |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | Data Communications ICs |
| 中文描述： | 數據通信集成電路 |
| 文件頁數： | 61/126頁 |
| 文件大?。?/td> | 730K |
| 代理商： | SAB82525H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁
Semiconductor Group
61
SAB 82525
SAB 82526
SAF 82525
SAF 82526
Since a transmitted zero is given priority over a 1 due to the OR connection at the bus, and
since the individually combined stations in the address field of the transmitted HDLC frame
differ from one another, the fact that a collision has occurred will be detected prior to or at the
latest within the address field. The frame of the transmitter with the highest temporary priority
(address field) is not affected and is transmitted without interruptions. All other transmitters
terminate their operation immediately.
Note
: If a wired OR connection has been realized by an external pull-up resistor without decoupling,
the data output (T
×
DA/T
×
DB) can be used as an open drain output and connected directly to
the C
×
DA, C
×
DB input.
Priority Principle
When the HDLC frame has been successfully transmitted by the HSCX, the priority is
decremented. In order to transmit an additional frame, ten successive 1’s must be present on
the bus. This fact is used as a criterion to ensure that the higher priority transmitters do not
contain any transmit requests. It is now possible to transmit a frame and the priority can be
increased again (8 successive 1’s). This method offers a priority allocation based on the
selection of a particular address. It also ensures that each subscriber can access the bus at a
pre-determinable time.
Timing Modes
If a bus configuration has been selected, the HSCX provides two timing modes, differing in the
period between sending data and evaluation of the transmitted data for collision detection.
timing mode 1 (CCR1: SC1, SC0 = 01)
Data is output with the rising edge of the transmit clock via the T
×
D pins, and evaluated
1/2 clock period later with the falling clock edge at the C
×
D pins.
timing mode 2 (CCR1: SC1, SC0 = 11)
Data is output with the falling clock edge and evaluated with the next falling clock edge.
Thus one complete clock period is available during data output and their evaluation.
Note:
If the bus is occupied by other transmitters and/or there is no transmit request in the HSCX, log 1
will be continuously transmitted at the T
×
DA/T
×
DB output.
Bus Access Procedure
The idle state of the bus is identified by eight or more successive 1’s. In case of a transmit re-
quest in the HSCX, the frame is transmitted and the bus is identified as busy with the first zero
of the opening flag (start flag).
After the frame has been transmitted, the bus becomes available again by transmitting 1’s.
Collisions
During the transmitting process, the data transmitted from the HSCX is compared with the data
on the bus. In case an erroneous bit is detected (log 1 sent and log 0 detected, or vice versa)
the frame is immediately aborted, and idle (log 1) is transmitted. Transmission will be initiated
again by the HSCX as soon as possible.
相關PDF資料 |
PDF描述 |
|---|---|
| SAF82532H-10 | ICs for Communications |
| SAB82532 | ICs for Communications |
| SAB82532H | ICs for Communications |
| SAB82532N | ICs for Communications |
| SAB82532N-10 | ICs for Communications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAB82525HV2.1 | 制造商:Infineon Technologies AG 功能描述:PROTOCOL CONTROLLER, 44 Pin, QFP 制造商:Siemens 功能描述:PROTOCOL CONTROLLER, 44 Pin, QFP |
| SAB82525HV2.2 | 功能描述:輸入/輸出控制器接口集成電路 T/E RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| SAB82525H-V21 | 功能描述:IC CONTROLLER SERIAL 44-MQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| SAB82525HV21DHSCX | 制造商:Infineon Technologies AG 功能描述: |
| SAB82525HV22 | 制造商:Infineon Technologies AG 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。