參數資料
型號: SAA7826HL
廠商: NXP Semiconductors N.V.
元件分類: DRAM
英文描述: CD audio decoder, digital servo and filterless DAC with integrated pre-amp and laser control
封裝: SAA7826HL/M1AS/S5<SOT315-1 (LQFP80)|<<http://www.nxp.com/packages/SOT315-1.html<1<Always Pb-free,;
文件頁數: 35/89頁
文件大?。?/td> 379K
代理商: SAA7826HL
2003 Oct 01
35
Philips Semiconductors
Product specification
CD audio decoder, digital servo and filterless
DAC with integrated pre-amp and laser control
SAA7826
7.16.9.4
Automatic sequencers and timer interrupts
Two automatic sequencers are implemented (and must be
initialized after power-on):
Auto-start sequencer: controls the start-up of focus,
radial and motor
Auto-stop sequencer: brakes the disc and shuts down
the servos.
When the automatic sequencers are not used it is possible
to generate timer interrupts, defined by the
time_parameter coefficient.
7.16.9.5
High-level status
Thereadhigh-levelstatus commandcanbeused toobtain
the interrupt, decoder, autosequencer status registers and
the motor start time. Use of the read high-level status
command clears the interrupt status register, and
re-enables the subcode read via a servo command.
7.16.10 D
RIVER INTERFACE
The control signals (pins RA, FO and SL) for the
mechanism actuators are pulse density modulated. The
modulating frequency can be set to either 1.0584 or
2.1168 MHz; controlled via the xtra_preset parameter.
An analog representation of the output signals can be
achieved by connecting a 1st-order low-pass filter to the
outputs.
During reset (i.e. RESET pin is held LOW) the RA, FO and
SL pins are high-impedance. At all other times, when the
laser is switched off, the RA and FO pins output a 2 MHz
50% duty factor signal.
7.16.11 L
ASER INTERFACE
The laser diode pre-amplifier function is built into the
SAA7826; see Fig.23. The current can be regulated, up to
120 mA [programmed via new shadow register A (bank 2)
and register 3 (bank 3)], in four steps ranging from 58% up
to full power. New shadow register A (bank 2) and
register 3 (bank 3)] are used to select the step values.
The voltage derived from the monitor diode is maintained
at a steady state by the laser drive circuitry, by regulating
the current through the laser diode. The type of monitor
diodebeingused(150 mVor180 mV)mustbeselectedby
new shadow register 7 (bank 2) (reset state = 150 mV).
The laser can be switched on or off by the xtra_preset
parameter; it is automatically driven if the focus control
loop is active.
相關PDF資料
PDF描述
SAA7893 Super audio media player
SAA7893HL Super audio media player
SAA8112HL Digital Camera Signal Processor and Microcontroller(數字照相信號處理器和微控制器)
SAA8113HL Digital PC-camera signal processor(數字PC照相信號處理器)
SAA8115HL Digital Camera USB Interface(數字照相USB接口)
相關代理商/技術參數
參數描述
SAA7826HL/E/M1A 功能描述:音頻數/模轉換器 IC PHONIC AUTO RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel
SAA7826HL/E/M1A,55 功能描述:音頻數/模轉換器 IC PHONIC AUTO RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel
SAA7826HL/M1A 功能描述:音頻數/模轉換器 IC PHONIC AUTO RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel
SAA7826HL/M1A,557 功能描述:音頻數/模轉換器 IC PHONIC AUTO RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel
SAA7826HL/M1AS/S5, 制造商:NXP Semiconductors 功能描述:- Tape and Reel 制造商:NXP Semiconductors 功能描述:DSP