參數資料
型號： SAA2520GP
廠商： NXP SEMICONDUCTORS
元件分類： 消費家電
英文描述： Stereo filter and codec for MPEG layer 1 audio applications
中文描述： SPECIALTY CONSUMER CIRCUIT, PQFP44
封裝： 14 X 14 X 2.20 MM, PLASTIC, QFP-44
文件頁數： 35/36頁
文件大?。?/td> 151K
代理商： SAA2520GP
August 1993
35
Philips Semiconductors
Preliminary specification
Stereo filter and codec for MPEG layer 1
audio applications
SAA2520
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook”(order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all QFP
packages.
The choice of heating method may be influenced by larger
plastic QFP packages (44 leads, or more). If infrared or
vapour phase heating is used and the large packages are
not absolutely dry (less than 0.1% moisture content by
weight), vaporization of the small amount of moisture in
them can cause cracking of the plastic body. For more
information, refer to the Drypack chapter in our “Quality
Reference Handbook”(order code 9397 750 00192).
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°
C.
Wave soldering
Wave soldering is
not
recommended for QFP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering cannot be avoided, the following
conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The footprint must be at an angle of 45
°
to the board
direction and must incorporate solder thieves
downstream and at the side corners.
Even with these conditions, do not consider wave
soldering the following packages: QFP52 (SOT379-1),
QFP100 (SOT317-1), QFP100 (SOT317-2),
QFP100 (SOT382-1) or QFP160 (SOT322-1).
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料
PDF描述
SAA2520 Stereo filter and codec for MPEG layer 1 audio applications
SAA3004 Remote control transmitter
SAA3004P Remote control transmitter
SAA3004T Remote control transmitter
SAA3007 INFRARED REMOTE CONTROL TRANSMITTER (LOW VOLTAGE)
相關代理商/技術參數
參數描述
SAA2521 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Masking threshold processor for MPEG layer 1 audio compression applications
SAA2521GP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Masking threshold processor for MPEG layer 1 audio compression applications
SAA2531DEB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic
SA-A2870-FREQ 制造商:NEL 制造商全稱:Nel Frequency Controls,inc 功能描述:Differential Positive ECL (DPECL)
SA-A2871-FREQ 制造商:NEL 制造商全稱:Nel Frequency Controls,inc 功能描述:Differential Positive ECL (DPECL)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*