- 您現在的位置：買賣IC網 > PDF目錄372102 > SA5217 (NXP Semiconductors N.V.) Postamplifier with link status indicator PDF資料下載
參數資料
| 型號： | SA5217 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Postamplifier with link status indicator |
| 中文描述： | 后置連接狀態(tài)指示燈與 |
| 文件頁數： | 3/12頁 |
| 文件大小： | 98K |
| 代理商： | SA5217 |
Philips Semiconductors
Product specification
SA5217
Postamplifier with link status indicator
1998 Oct 07
3
PIN DESCRIPTIONS
PIN
NO.
1
LED
SYMBOL
DESCRIPTION
Output for the LED driver. Open collector output transistor with 125
series limiting resistor. An above threshold signal
turns this transistor ON.
Capacitor for the peak detector. The value of this capacitor determines the detector response time to the signal, supple-
menting the internal 10pF capacitor.
Peak detector threshold resistor. The value of this resistor determines the threshold level of the peak detector.
Device analog ground pin.
Peak detector digital output. When this output is LOW, there is data present above the threshold. This pin is normally
connected to the JAM pin and has a TTL fanout of two.
Input to inhibit data flow. Sending the pin HIGH forces TTL DATA OUT ON, Pin 10, LOW. This pin is normally connected
to the FLAG pin and is TTL-compatible.
Power supply pin for the digital portion of the chip.
Power supply pin for the analog portion of the chip.
Device digital ground pin.
TTL output pin with a fanout of five.
Peak detector current resistor. The value of this resistor determines the amount of discharge current available to the
peak detector capacitor, C
PKDET
.
Peak detector hysteresis resistor. The value of this resistor determines the amount of hysteresis in the peak detector.
Non-inverting input to amplifier A8.
Non-inverting output of amplifier A2.
Inverting input to amplifier A8.
Inverting output of amplifier A2.
Auto-Zero capacitor pin (Negative terminal). The value of this capacitor determines the low-end frequency response of
the preamp A1.
Auto-Zero capacitor pin (Positive terminal). The value of this capacitor determines the low-end frequency response of the
preamp A1.
Non-inverting input of the preamp A1.
Inverting input of the preamp A1.
2
C
PKDET
3
4
5
THRESH
GND
A
FLAG
6
JAM
7
8
9
10
11
V
CCD
V
CCA
GND
D
V
OUT
R
PKDET
12
13
14
15
16
17
R
HYST
IN
8A
OUT
2A
IN
8B
OUT
2B
C
AZN
18
C
AZP
19
20
IN
1A
IN
1B
BLOCK DIAGRAM
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A1
A2
A3
A4
A5
A6
A7
GATED AMP
SCHMITT TRIGGER
OUTPUT DISABLE
PEAK DETECT
LED DRIVER
HYSTERESIS
V
CCA
V
CCD
OUT
2A
OUT
2B
A8
IN
8B
IN
8A
V
OUT
JAM
FLAG
LED
IN
1B
IN
1A
C
AZP
C
AZN
R
PKDET
GND
A
GND
D
THRESH
C
PKDET
R
HYST
SD00355
Figure 2. Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| SA5217D | Postamplifier with link status indicator |
| SA5222 | Low-Power FDDI Transimpedance Amplifier(低功耗FDDI互阻抗放大器) |
| SA5223 | Wide Dynamic Range AGC Transimpedance Amplifier (150MHz)(寬動態(tài)范圍AGC互阻抗放大器(150MHz)) |
| SA5223D | Wide dynamic range AGC transimpedance amplifier 150MHz |
| SA5230FE | Low Voltage Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA5217D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Postamplifier with link status indicator |
| SA5217D,602 | 功能描述:高速運算放大器 POST AMP WITH LINK STATUS IND RoHS:否 制造商:NXP Semiconductors 通道數量: 電壓增益 dB: 輸入補償電壓: 轉換速度: 工作電源電壓: 電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SO-20 封裝:Tube 產品: |
| SA5217D/01 | 功能描述:特殊用途放大器 POST AMP W/LINK STATUS RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| SA5217D/01,112 | 功能描述:特殊用途放大器 POST AMP W/LINK RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| SA5217D/01,118 | 功能描述:特殊用途放大器 POST AMP W/LINK RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。