- 您現在的位置：買賣IC網 > PDF目錄374665 > S3067 (Applied Micro Circuits Corp.) Multirate SONET/SDH/ATM Transceiver with FEC(帶正向糾錯功能的多速率SONET/SDH/ATM收發器) PDF資料下載
參數資料
| 型號： | S3067 |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | Multirate SONET/SDH/ATM Transceiver with FEC(帶正向糾錯功能的多速率SONET/SDH/ATM收發器) |
| 中文描述： | 多速率的SONET / SDH / ATM的收發器與前向糾錯（帶正向糾錯功能的多速率的SONET / SDH / ATM的收發器） |
| 文件頁數： | 7/27頁 |
| 文件大小： | 246K |
| 代理商： | S3067 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
7
S3067
MULTIRATE (OC-48/24/12/3/GBE) SONET/SDH/ATM TRANSCEIVER WITH FEC
October 26, 2000 / Revision A
Parallel-to-Serial Converter
The parallel-to-serial converter shown in Figure 4 is
comprised of a FIFO and a parallel-to-serial register.
The FIFO input latches the data from the PIN[15:0]
bus on the rising edge of PICLK. The parallel-to-
serial register is a loadable shift register which takes
its parallel input from the FIFO output.
An internally generated divide-by-16 clock, which is
phase aligned to the transmit serial clock as de-
scribed in the Timing Generator description, activates
the parallel data transfer between registers. The serial
data is shifted out of the parallel-to-serial register at
the TSCLK rate
.
FIFO
A FIFO is added to decouple the internal and exter-
nal (PICLK) clocks. The internally generated
divide-by-16 clock is used to clock out data from the
FIFO. PHINIT and LOCKDET are used to center or
reset the FIFO. The PHINIT and LOCKDET signals
will center the FIFO after the third PICLK pulse. This
is in order to insure that PICLK is stable. This
scheme allows the user to have an infinite PCLK to
PICLK delay through the ASIC. Once the FIFO is
centered, the PCLK to PICLK delay can have a
maximum drift specified by Table 20.
FIFO Initialization
The FIFO can be initialized in one of the following
three ways:
1.During power up, once the PLL has locked to the
reference clock provided on the REFCLK pins, the
LOCKDET will go active and initialize the FIFO.
2.When RSTB goes active, the entire chip is reset.
This causes the PLL to go out of lock and thus the
LOCKDET goes inactive. When the PLL reac-
quires the lock, the LOCKDET goes active and
initializes the FIFO. Note: PCLK is held reset when
RSTB is active.
3.The user can also initialize the FIFO by raising
PHINIT.
During the normal running operation, the incoming
data is passed from the PICLK timing domain to the
internally generated divide by 16 clock timing do-
main. Although the frequency of PICLK and the
internally generated clock is the same, their phase
relationship is arbitrary. To prevent errors caused by
short setup or hold times between the two timing
domains, the timing generator circuitry monitors the
phase relationship between PICLK and the internally
generated clock. When a potential setup or hold time
violation is detected, the phase error goes high.
When PHERR conditions occur, PHINIT should be
activated to recenter the FIFO (at least 2 PCLK peri-
ods). This can be done by connecting PHERR to
PHINIT. When realignment occurs up to 10 bytes of
data will be lost. The user can also take in the
PHERR signal, process it and send an output to
PHINIT in such a way that idle bytes are lost during
the realignment process. PHERR will go inactive
when the realignment is complete.
RECEIVER OPERATION
The S3067 receiver chip provides the first stage of
digital processing of a receive SONET STS-48/STS-
24/STS-12/STS-3/GBE bit-serial stream. The bit
serial data stream is then converted into a 16 bit
half-word data format. A loopback mode is provided
for diagnostic loopback (transmitter to receiver). A
line loopback (receiver to transmitter) is also pro-
vided. Both line and local loopback modes can be
active at the same time.
Serial-to-Parallel Converter
The serial-to-parallel converter consists of two 16-bit
registers. The first is a serial-in, parallel-out shift reg-
ister, which performs the serial-to-parallel conversion
clocked by the clock recovery block. On the falling
edge of the POCLK, the data in the parallel register
is transferred to an output parallel register which
drives POUT[15:0].
OTHER OPERATING MODES
Diagnostic Loopback
When the Diagnostic Loopback Enable (DLEB) input
is low, a loopback from the transmitter to the re-
ceiver at the serial data rate can be set up for
diagnostic purposes. The differential serial output
data from the transmitter is routed to the serial-to-
parallel block in place of the normal data stream
(RSD). TSD/TSCLK outputs are active. DLEB takes
precedence over SDPECL and SDTTL.
相關PDF資料 |
PDF描述 |
|---|---|
| S3076 | Multi-Rate SONET/SDH Clock Recovery Unit(多速率SONET/SDH時鐘恢復單元) |
| S3083 | SONET/SDH/ATM OC-48 16：1 Transmitter(帶片上高頻鎖相環的SONET/SDH 16選1傳送器) |
| S3528WH-EA | 3528 Size Flash White Color SMD Type LED |
| S3A_1 | 3.0 AMPS. Surface Mount Rectifiers |
| S3A | 3.0 AMPS. Surface Mount Rectifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S3067TB-156TBGA20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIRATE (OC-48/24/12/3/GBE/FC) SONET/SDH/ATM TRANSCEIVER w/ FEC |
| S3067TB20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIRATE (OC-48/24/12/3/GBE/FC) SONET/SDH/ATM TRANSCEIVER w/ FEC |
| S30680 | 制造商:Microsemi Corporation 功能描述:800V 70A 2PIN DO-203AB - Bulk |
| S306AB | 制造商:Cinch Connectors 功能描述:Conn Wire to Board SKT 6 POS Solder Lug ST Panel Mount |
| S-306-AB | 功能描述:Jones 插頭和插槽 6C PNL MNT SOCKET RoHS:否 制造商:Molex 產品類型:Socket Connectors 系列:Beau 位置/觸點數量:8 電壓額定值:250 V 電流額定值:10 A 外殼材料:Thermoplastic 觸點材料:Phosphor Bronze 觸點電鍍:Tin-Lead |
發布緊急采購，3分鐘左右您將得到回復。