參數資料
型號： S29PL127J60
廠商： Spansion Inc.
英文描述： CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
中文描述： 3.0伏的CMOS只，同步讀/寫閃存與增強VersatileIO控制記憶
文件頁數： 68/106頁
文件大?。?/td> 1997K
代理商： S29PL127J60
66
S29PL127J/S29PL129J/S29PL064J/S29PL032J
31107A62 April 7, 2005
P R E L I M I N A R Y
operation. The program command sequence should be reinitiated once that bank
has returned to the read mode, to ensure data integrity. Note that the SecSi Sec-
tor, autoselect and CFI functions are unavailable when the SecSi Sector is
enabled.
Programming is allowed in any sequence and across sector boundaries.
A bit
cannot be programmed from “0” back to a “1.”
Attempting to do so may
cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate
the operation was successful. However, a succeeding read will show that the data
is still “0.” Only erase operations can convert a “0” to a “1.”
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program data to a bank faster
than using the standard program command sequence. The unlock bypass com-
mand sequence is initiated by first writing two unlock cycles. This is followed by
a third write cycle containing the unlock bypass command, 20h. That bank then
enters the unlock bypass mode. A two-cycle unlock bypass program command
sequence is all that is required to program in this mode. The first cycle in this se-
quence contains the unlock bypass program command, A0h; the second cycle
contains the program address and data. Additional data is programmed in the
same manner. This mode dispenses with the initial two unlock cycles required in
the standard program command sequence, resulting in faster total programming
time.
Table 21
shows the requirements for the command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock By-
pass Reset commands are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset command sequence. (See Table 22)
The device offers accelerated program operations through the WP#/ACC pin.
When the system asserts V
HH
on the WP#/ACC pin, the device automatically en-
ters the Unlock Bypass mode. The system may then write the two-cycle Unlock
Bypass program command sequence. The device uses the higher voltage on the
WP#/ACC pin to accelerate the operation.
Note that the WP#/ACC pin must not
be at V
HH
any operation other than accelerated programming, or device damage
may result. In addition, the WP#/ACC pin must not be left floating or uncon-
nected; inconsistent behavior of the device may result.
4 illustrates the algorithm for the program operation. Refer to the "
Erase/Program
Operations
" section table in the AC Characteristics section for parameters, and
Figure 14
for timing diagrams.
相關PDF資料
PDF描述
S29PL127J65 CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
S29PL127J70 CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
S2A_1 2.0 AMPS. Surface Mount Rectifiers
S2K 2.0 AMPS. Surface Mount Rectifiers
S2M 2.0 AMPS. Surface Mount Rectifiers
相關代理商/技術參數
參數描述
S29PL127J60BAI000 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 60NS 80FBGA - Bulk
S29PL127J60BFI000 制造商:Spansion 功能描述:FLASH PARALLEL - Bulk
S29PL127J60TAI130 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 8MX16 60NS 56TSOP - Trays
S29PL127J60TFI130 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 128M-Bit 8M x 16 60ns 56-Pin TSOP Tray
S29PL127J65 制造商:SPANSION 制造商全稱:SPANSION 功能描述:CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*