- 您現在的位置：買賣IC網 > PDF目錄365393 > S29GL128N10FFIV23 (SPANSION LLC) 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology PDF資料下載
參數資料
| 型號： | S29GL128N10FFIV23 |
| 廠商： | SPANSION LLC |
| 元件分類： | DRAM |
| 英文描述： | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
| 中文描述： | 8M X 16 FLASH 3V PROM, 100 ns, PBGA64 |
| 封裝： | 13 X 11 MM, 1MM PITCH, LEAD FREE, FBGA-64 |
| 文件頁數： | 61/100頁 |
| 文件大小： | 952K |
| 代理商： | S29GL128N10FFIV23 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
S29GL-N_00_B3 October 13, 2006
S29GL-N MirrorBit Flash Family
59
D a t a S h e e t
In the erase-suspend-read mode, the system can also issue the autoselect command se-
quence. Refer to the
Autoselect Mode on page 37
section and
Autoselect Command
Sequence on page 51
for details.
To resume the sector erase operation, the system must write the Erase Resume command.
The address of the erase-suspended sector is required when writing this command. Further
writes of the Resume command are ignored. Another Erase Suspend command can be written
after the chip has resumed erasing. It is important to allow an interval of at least 5 ms be-
tween Erase Resume and Erase Suspend.
Lock Register Command Set Definitions
The Lock Register Command Set permits the user to one-time program the Secured Silicon
Sector Protection Bit, Persistent Protection Mode Lock Bit, and Password Protection Mode Lock
Bit. The Lock Register bits are all readable after an initial access delay.
The
Lock Register Command Set Entry
command sequence must be issued prior to any
of the following commands listed, to enable proper command execution.
Note that issuing the
Lock Register Command Set Entry
command
disables reads and
w rites for the flash memory
.
Lock Register Program Command
Lock Register Read Command
The
Lock Register Command Set Exit
command must be issued after the execution of the
commands to reset the device to read mode. Otherwise the device hangs. If this happens,
the flash device must be reset. Please refer to RESET# for more information. It is important
to note that the device is in either Persistent Protection mode or Password Protection mode
depending on the mode selected prior to the device hang.
For either the Secured Silicon Sector to be locked, or the device to be permanently set to the
Persistent Protection Mode or the Password Protection Mode, the associated Lock Register bits
must be programmed. Note that only the Persistent Protection Mode Lock Bit
or
the Password
Protection Mode Lock Bit can be programmed. The Lock Register Program operation aborts if
there is an attempt to program both the Persistent Protection Mode and the Password Protec-
tion Mode Lock bits.
The Lock Register Command Set Exit command must be initiated to re-enable reads and
writes to the main memory.
Passw ord Protection Command Set Definitions
The Password Protection Command Set permits the user to program the 64-bit password, ver-
ify the programming of the 64-bit password, and then later unlock the device by issuing the
valid 64-bit password.
The
Passw ord Protection Command Set Entry
command sequence must be issued prior
to any of the commands listed following to enable proper command execution.
Note that issuing the
Passw ord Protection Command S et Entry
command
disabled
reads and w rites the main memory.
Passw ord Program Command
Passw ord Read Command
Passw ord Unlock Command
The Password Program command permits programming the password that is used as part of
the hardware protection scheme. The actual password is 64-bits long. There is no special ad-
dressing order required for programming the password.
The passw ord is programmed in
8-bit or 16-bit portions. Each portion requires a Passw ord Program Command.
相關PDF資料 |
PDF描述 |
|---|---|
| S29GL128N10TAI010 | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
| S29GL128N10TAI012 | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
| S29GL128N11FAI010 | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
| S29GL128N11FAI012 | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
| S29GL128N11FAI013 | 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL128N10TF101 | 制造商:Spansion 功能描述: |
| S29GL128N10TFI010 | 功能描述:IC FLASH 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:128Mb （16M x 8，8M x 16） 寫周期時間 - 字，頁:100ns 訪問時間:100ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:56-TFSOP（0.724"，18.40mm 寬） 供應商器件封裝:56-TSOP 標準包裝:91 |
| S29GL128N10TFI020 | 制造商:Spansion 功能描述:S29GL128N10TFI020 制造商:Spansion 功能描述:Flash - NOR IC |
| S29GL128N11FAI020 | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 128M-Bit 16M x 8/8M x 16 110ns 64-Pin Fortified BGA Tray |
| S29GL128N11FAI023 | 制造商:Spansion 功能描述:Flash Mem Parallel 3V/3.3V 128M-Bit 16M x 8/8M x 16 110ns 64-Pin Fortified BGA T/R |
發布緊急采購，3分鐘左右您將得到回復。