- 您現在的位置：買賣IC網 > PDF目錄374607 > S-2100R (Seiko Instruments Inc.) 64-bit FUSE ROM(64位熔絲ROM) PDF資料下載
參數資料
| 型號： | S-2100R |
| 廠商： | Seiko Instruments Inc. |
| 英文描述： | 64-bit FUSE ROM(64位熔絲ROM) |
| 中文描述： | 64位保險絲光盤（64位熔絲光盤） |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 63K |
| 代理商： | S-2100R |
64-bit FUSE ROM
S-2100R
4
Seiko Instruments Inc.
Read Mode Operation
Counter Hold Mode Operation
By setting the CE/PE terminal to
“
L
”
level, the S-2100R enters the read mode. *
1
Next, adding an RST pulse causes the
contents of the memory bit of address 1 to be output at the DATA terminal; the rising of the RST pulse latches the data and
stabilizes it. *
2
Reading of addresses from 2 to 64 can be done by adding a CLK pulse sequentially after reading address 1. *
3
As soon as address 64 has been read, the COUNTER OUT terminal outputs
“
H
”
level. When it finishes reading address 64,
it does not accept any more CLK pulses and the counter does not operate. The data of address 64 is maintained till address
1 is read by the RST pulse.
Figure 3 Read mode timing
Address 1 output
Address 3 output
Address 2 output
t
CES
t
ACC
t
CE
t
RC
t
ACC
t
CH
t
RC
t
RH
CE/P
RS
CL
DATA
Address 1 output
t
RS
t
RC
*1
When both the CLK and RST terminals are at “H” level.
When the RST terminal is at
“
L
”
level, the latch is transparent and the data is recognized by the rising of the RST pulse.
Data read by the CLK pulse is latched at its rising.
*2
*3
By setting the CE/PE terminal to
“
H
”
level, the S-2100R enters the counter hold mode and the DATA terminal becomes high
impedance. *
4
In counter hold mode, the CLK and RST pulses which fall while the CE/PE terminal is at “H” level are recognized to be invalid
and there is no change in counter and data output. When the CE/PE terminal is set to “L” level again, it returns to the
condition in which it was before the counter hold mode.
Figure 4 Counter hold mode timing
Address M
output
Address M+1 output
Address M+1 output
t
CES
t
CRI
CE/P
RST
CLK
DATA
t
WZ
t
CS
*
4
When both the CLK and RST terminals are at “H” level.
相關PDF資料 |
PDF描述 |
|---|---|
| S-22H10 | PARALLEL NON-VOLATILE RAM |
| S-22S10 | PARALLEL NON-VOLATILE RAM |
| S-22 | PARALLEL NON-VOLATILE RAM |
| S-22H | PARALLEL NON-VOLATILE RAM |
| S-22S | PARALLEL NON-VOLATILE RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S2-100RF1 | 制造商:Riedon 功能描述:RES 100 OHM 1W 1% WW SMD |
| S2-100RJ1 | 制造商:Riedon 功能描述:RES 100 OHM 1W 5% WW SMD |
| S2101 | 制造商:LAPP/CONTACT CONNECTORS 功能描述:SLN 29 (1inch) SKINTOP BLACK UL, CSA, CE |
| S-210-12 | 功能描述:線性和開關式電源 204W 12V 17A RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
| S-210-13.5 | 功能描述:線性和開關式電源 202.5W 13.5V 15A RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
發布緊急采購，3分鐘左右您將得到回復。