- 您現在的位置：買賣IC網 > PDF目錄378162 > RMPA0913C-58 (Electronic Theatre Controls, Inc.) 3.5V AMPS/CDMA Power Amplifier PDF資料下載
參數資料
| 型號： | RMPA0913C-58 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 3.5V AMPS/CDMA Power Amplifier |
| 中文描述： | 3.5V之間的AMPS / CDMA功放 |
| 文件頁數： | 3/6頁 |
| 文件大小： | 257K |
| 代理商： | RMPA0913C-58 |
Raytheon RF Components
362 Lowell Street
Andover, MA 01810
Revised March 30, 2000
Page 3
www.raytheon.com/micro
Characteristic performance data and specifications are subject to change without notice.
PRODUCT INFORMATION
CAUTION: LOSS OF GATE VOLTAGES (VG1, VG2) WHILE DRAIN VOLTAGES (VD1,VD2) ARE PRESENT MAY
DAMAGE THE AMPLIFIER.
The following sequence must be followed to properly test the amplifier:
Step 1:
Turn off RF input power.
Step 2:
Use GND terminal of the evaluation board for
the ground of the DC supplies. Slowly apply
gate supply voltages of -3.0 V to the board
terminals Vgg1, Vgg2 to pinch-off the two
stages.
Step 3:
Slowly apply drain supply voltage of +3.5 V to
the board terminals Vdd.
Step 4:
Adjust the gate supply voltages Vgg1, Vgg2 to
the values shown on the data summary supplied
with the sample. (First adjust Vgg2 to set Idq2.
Then adjust Vgg1 to set Iddq=Idq1+Idq2. These
gate voltages need not be changed. However,
Vgg1,Vgg2 may be adjusted only when different
quiescent bias currents are desired for
performance trade-off evaluation).
Step 5:
After the bias condition is established, RF input
signal may now be applied at the appropriate
frequency band. Adjust RF input signal power
level as required.
Step 6:
Follow turn-off sequence of:
(i) Turn off RF Input Power
(ii) Turn down and off drain voltage Vdd.
(iii) Turn down and off gate voltages Vgg1, Vgg2.
Test Procedure
for the evaluation board
(RMPA0913C-58)
Figure 3
Schematic
for a Typical Test
Evaluation Board
Evaluation Board Schematic
Ver.6, 4/28/98
Board Type: Multi Layer FR4
Signal to Ground Separation: 0.016”
RMPA0913C-58
3.5V AMPS/CDMA Power Amplifier
相關PDF資料 |
PDF描述 |
|---|---|
| RMWL38001 | 37-40 GHz Low Noise Amplifier MMIC |
| RN104PG103ES | THICK FILM CHIP RESISTORS |
| RN104PG103GS | THICK FILM CHIP RESISTORS |
| RN104PK103AS | THICK FILM CHIP RESISTORS |
| RN104PK103CS | THICK FILM CHIP RESISTORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RMPA0951AT | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:3V Cellular CDMA PowerEdge Power Amplifier Module |
| RMPA0959 | 功能描述:射頻放大器 3.5V AMPS/CDMA PA Module RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| RMPA0963 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Cellular CDMA, CDMA2000-1X and WCDMA Power Amplifier Module |
| RMPA0965 | 功能描述:射頻放大器 CDMA-CDMA2000-1X Pwr Edge Amp Mod RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| RMPA0966 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:WCDMA Band V Power Amplifier Module |
發布緊急采購，3分鐘左右您將得到回復。