參數資料
型號: RLF12560T-2R7N110
廠商: National Semiconductor Corporation
英文描述: SOLID TANTALUM RoHS Compliant: Yes
中文描述: N溝道場效應管同步降壓穩壓控制器輸出電壓低
文件頁數: 2/22頁
文件大?。?/td> 602K
代理商: RLF12560T-2R7N110
Connection Diagram
20049411
14-Lead Plastic TSSOP
θ
= 155C/W
NS Package Number MTC14
Pin Description
BOOT (Pin 1)
- Supply rail for the N-channel MOSFET gate
drive. The voltage should be at least one gate threshold
above the regulator input voltage to properly turn on the
high-side N-FET.
LG (Pin 2)
- Gate drive for the low-side N-channel MOSFET.
This signal is interlocked with HG to avoid shoot-through
problems.
PGND (Pins 3, 13)
- Ground for FET drive circuitry. It should
be connected to system ground.
SGND (Pin 4)
- Ground for signal level circuitry. It should be
connected to system ground.
V
CC
(Pin 5)
- Supply rail for the controller.
PWGD (Pin 6)
- Power Good. This is an open drain output.
The pin is pulled low when the chip is in UVP, OVP, or UVLO
mode. During normal operation, this pin is connected to V
CC
or other voltage source through a pull-up resistor.
ISEN (Pin 7)
- Current limit threshold setting. This sources a
fixed 50μA current. A resistor of appropriate value should be
connected between this pin and the drain of the low-side
FET.
EAO (Pin 8)
- Output of the error amplifier. The voltage level
on this pin is compared with an internally generated ramp
signal to determine the duty cycle. This pin is necessary for
compensating the control loop.
SS (Pin 9)
- Soft start pin. A capacitor connected between
this pin and ground sets the speed at which the output
voltage ramps up. Larger capacitor value results in slower
output voltage ramp but also lower inrush current.
FB (Pin 10)
- This is the inverting input of the error amplifier,
which is used for sensing the output voltage and compen-
sating the control loop.
FREQ (Pin 11)
- The switching frequency is set by connect-
ing a resistor between this pin and ground.
SD (Pin 12)
- IC Logic Shutdown. When this pin is pulled low
the chip turns off the high side switch and turns on the low
side switch. While this pin is low, the IC will not start up. An
internal 20μA pull-up connects this pin to V
CC
.
HG (Pin 14)
- Gate drive for the high-side N-channel MOS-
FET. This signal is interlocked with LG to avoid shoot-
through problems.
L
www.national.com
2
相關PDF資料
PDF描述
RLF7030T-3R3M4R1 PCB COPPER CLAD 18 X 18 2 SIDE
RLF7030T-4R7M3R4 PCB COPPER CLAD 3 X 4.5 2 SIDE
RLP03N06CLE 0.3A, 60V, 6 Ohm, ESD Rated, Current Limited, Voltage Clamped, Logic Level N-Channel Power MOSFETs(0.3A, 60V, 6Ω , ESD 額定,電流限制,電壓箝位,邏輯電平N溝道功率MOS場效應管)
RLD03N06CLE 0.3A, 60V, 6 Ohm, ESD Rated, Current Limited, Voltage Clamped, Logic Level N-Channel Power MOSFETs(0.3A, 60V, 6Ω , ESD 額定,電流限制,電壓箝位,邏輯電平N溝道功率MOS場效應管)
RLD03N06CLESM 0.3A, 60V, 6 Ohm, ESD Rated, Current Limited, Voltage Clamped, Logic Level N-Channel Power MOSFETs(0.3A, 60V, 6Ω , ESD 額定,電流限制,電壓箝位,邏輯電平N溝道功率MOS場效應管)
相關代理商/技術參數
參數描述
RLF12560T-4R2N100 功能描述:固定電感器 4.2uH 10AMPS RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
RLF12560T-4R2N100-PF 制造商:TDK 功能描述:Inductor SMD RLF12560 4,2uH 10A
RLF12560T-5R6N9R2 功能描述:固定電感器 5.6uH 9.2AMPS RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
RLF12560T-5R6N9R2-PF 制造商:TDK 功能描述:Inductor SMD RLF12560 5,6uH 9,2A
RLF12560T-7R8N8R2 功能描述:固定電感器 7.8uH 8.2AMPS RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm