- 您現在的位置：買賣IC網 > PDF目錄69314 > R5F64115DFB 32-BIT, FLASH, 50 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | R5F64115DFB |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-BIT, FLASH, 50 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件頁數： | 71/84頁 |
| 文件大?。?/td> | 1206K |
| 代理商： | R5F64115DFB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁當前第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
87
ATmega48PA/88PA/168PA [DATASHEET]
9223F–AVR–04/14
An interrupt can be generated each time the counter value reaches the TOP value by using the OCF0A flag. If the interrupt
is enabled, the interrupt handler routine can be used for updating the TOP value. However, changing TOP to a value close to
BOTTOM when the counter is running with none or a low prescaler value must be done with care since the CTC mode does
not have the double buffering feature. If the new value written to OCR0A is lower than the current value of TCNT0, the
counter will miss the compare match. The counter will then have to count to its maximum value (0xFF) and wrap around
starting at 0x00 before the compare match can occur.
For generating a waveform output in CTC mode, the OC0A output can be set to toggle its logical level on each compare
match by setting the compare output mode bits to toggle mode (COM0A1:0 = 1). The OC0A value will not be visible on the
port pin unless the data direction for the pin is set to output. The waveform generated will have a maximum frequency of
fOC0 =fclk_I/O/2 when OCR0A is set to zero (0x00). The waveform frequency is defined by the following equation:
The N variable represents the prescale factor (1, 8, 64, 256, or 1024).
As for the normal mode of operation, the TOV0 flag is set in the same timer clock cycle that the counter counts from MAX to
0x00.
15.7.3 Fast PWM Mode
The fast pulse width modulation or fast PWM mode (WGM02:0 = 3 or 7) provides a high frequency PWM waveform
generation option. The fast PWM differs from the other PWM option by its single-slope operation. The counter counts from
BOTTOM to TOP then restarts from BOTTOM. TOP is defined as 0xFF when WGM2:0 = 3, and OCR0A when WGM2:0 = 7.
In non-inverting compare output mode, the output compare (OC0x) is cleared on the compare match between TCNT0 and
OCR0x, and set at BOTTOM. In inverting compare output mode, the output is set on compare match and cleared at
BOTTOM. Due to the single-slope operation, the operating frequency of the fast PWM mode can be twice as high as the
phase correct PWM mode that use dual-slope operation. This high frequency makes the fast PWM mode well suited for
power regulation, rectification, and DAC applications. High frequency allows physically small sized external components
(coils, capacitors), and therefore reduces total system cost.
In fast PWM mode, the counter is incremented until the counter value matches the TOP value. The counter is then cleared at
the following timer clock cycle. The timing diagram for the fast PWM mode is shown in Figure 15-6. The TCNT0 value is in
the timing diagram shown as a histogram for illustrating the single-slope operation. The diagram includes non-inverted and
inverted PWM outputs. The small horizontal line marks on the TCNT0 slopes represent compare matches between OCR0x
and TCNT0.
Figure 15-6. Fast PWM Mode, Timing Diagram
fOCnx
fclk_I/O
2 N
1 OCRnx
+
()
×
----------------------------------------------------
=
1234567
TCNTn
(COMnx1:0 = 2)
(COMnx1:0 = 3)
OCnx
Period
OCRnx Update and
TOVn Interrupt Flag Set
OCRnx Interrupt
Flag Set
相關PDF資料 |
PDF描述 |
|---|---|
| R5F64114NFB | 32-BIT, FLASH, 50 MHz, MICROCONTROLLER, PQFP100 |
| R5F64112DFB | 32-BIT, FLASH, 50 MHz, MICROCONTROLLER, PQFP100 |
| R5F64165PFD | 64-BIT, FLASH, MICROCONTROLLER, PQFP144 |
| R5F64168HNFB | 64-BIT, FLASH, MICROCONTROLLER, PQFP100 |
| R5F64168HDFB | 64-BIT, FLASH, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R5F64115DFB#U0 | 功能描述:MCU 384KB ROM 40KB RAM 100-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C/R32C/100/111 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| R5F64115NFB | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
| R5F64116DFB | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
| R5F64116DFB#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 16-Bit R8C CISC 512KB Flash 3.3V/5V 100-Pin LQFP Tray 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 512K I-TEMP PB-FREE 100-LQFP - Trays 制造商:Renesas Electronics Corporation 功能描述:MCU 16BIT 512KB FLASH 100LFQFP |
| R5F64116NFB | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
發布緊急采購，3分鐘左右您將得到回復。