- 您現在的位置：買賣IC網 > PDF目錄361325 > QT310 (Electronic Theatre Controls, Inc.) PROGRAMMABLE CAPACITANCE SENSOR IC PDF資料下載
參數資料
| 型號： | QT310 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | PROGRAMMABLE CAPACITANCE SENSOR IC |
| 中文描述： | 可編程電容傳感器IC |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 837K |
| 代理商： | QT310 |
DISA / DISB:
Because the DI counters count at the burst rate,
slow burst spacings can result in very long detection delays
with terminal counts above 1. To cure this problem, the burst
rate can be made faster while DIA or DIB are counting. This
creates the effect of a gear-shifted detection process: normal
speed when there are no threshold crossings, and fast mode
when a detection is pending.
DISA and DISB respectively gearshift the effect of DIA and
DIB. The gear-shifting ceases and normal speed resumes
once the detection is confirmed (DIA = DIAT) and once the
detection ceases (DIB = DIBT).
When SC=0 the device operates without any sleep cycles,
and so the timebase for the DI counters is very fast.
2.6 MAX ON-DURATION (MOD)
Range: 0..255; Default: 14; 255 disables
Affects parameter Tmod, the calibration delay time
If a stray object remains on or near the sense electrode, the
signal may rise enough to activate the OUT pin thus
preventing normal operation. To provide a way around this, a
Max On-Duration (‘MOD’) timer is provided to cause a
recalibration if the activation lasts longer than the designated
timeout, Tmod.
The MOD function can also be disabled, in which case the
sensor will never recalibrate unless the part is powered down
and back up again. In infinite timeout the designer should take
care to ensure that drift in Cs, Cx, and Vdd do not cause the
device to ‘stick on’ inadvertently when the target object is
removed from the sense field.
MOD is expressed in multiples of the burst space interval,
which can be either Tbs or Tbd depending on the Sleep
Cycles setting (SC).
If SC > 0, the delay is:
Tmod = (MOD + 1) x 16 x Tbs
Example:
Tbs = 100ms,
MOD = 9;
Tmod = (9 + 1) x 16 x 100ms = 160 secs.
If SC = 0, Tmod is a function of the total combined burst
durations, Tbd. If SC = 0, the delay is:
Tmod = (MOD + 1) x 256 x Tbd
Example:
Tbd = 18ms,
MOD = 9;
Tmod = (9 + 1) x 256 x 18ms = 46 secs.
If MOD = 255, recalibration timeout = infinite (disabled)
regardless of SC.
An MOD induced recalibration will make the OUT pin inactive
except if the output is set to toggle mode (Section 2.7.2), in
which case the OUT state will be unaffected but the sensor
will have recalibrated.
2.7 OUTPUT FEATURES
Available output processing options accommodate most
requirements; these can be set via the clone process.
If TOG and TOGL modes are disabled, OUT responds to
detections with a steady-state active logic level which lasts for
the duration of a detection, until a MOD timeout occurs
(Section 2.6).
The OUT pin is push-pull CMOS.
2.7.1 P
OLARITY
(OUTP)
Options: active-low or -high; Default: active-low
The polarity of OUT can be set via option OUTP using the
cloning process. Either active-low or active-high can be
selected. This not the same as ‘direction of signal detection’
(Section 2.8.1).
In ‘a(chǎn)ctive high’ mode the normal, inactive polarity of OUT is
low; in ‘a(chǎn)ctive low’ mode the normal, inactive polarity of OUT
is high.
OUTP also selects the initial state of OUT when the sensor is
used in Toggle or Toggle Latch modes (Sections 2.7.2, 2.7.3);
for example, if OUTP is set active-low, the initial state of OUT
after power-up will be high.
2.7.2 T
OGGLE
M
ODE
(TOG)
Options: enabled or disabled; Default: disabled
Toggle mode gives the OUT pin a touch-on / touch-off flip-flop
action, so that its state changes with each new detection. It is
most useful for controlling power loads, for example kitchen
appliances, power tools, light switches, etc.
MOD time-outs (Section 2.6) and the /CAL_CLR pin will
recalibrate the sensor but leave the OUT state unchanged.
The OUTP option (Section 2.7.1) sets the initial state of the
sensor after power-up.
2.7.3 T
OGGLE
L
ATCH
M
ODE
(TOGL)
Options: enabled or disabled; Default: disabled
In this mode, OUT becomes active when a valid detection
occurs but will only go inactive again if an external clear signal
is applied to the part; further detections after the first one will
not change the state of OUT.
The external clear signal is applied to the
/CAL_CLR
pin
which functions only as latch clear input if TOGL is enabled.
The only way to recalibrate the sensor externally in TOGL
mode is to cycle power off and back on.
A logic low pulse on
/CAL_CLR
will clear the latch and make
OUT inactive. As the
/CAL_CLR
pin is sampled once per
burst, the clear pulse has to be at least as long as Tbs (the
burst duration) to ensure the latch clears.
If any underlying threshold detection remains active for longer
than the Max On-Duration (MOD) period the device will
recalibrate automatically, but the OUT pin will not change
state.
A clear pulse applied to
/CAL_CLR
will clear the latch even if
the part is in the process of recalibrating due to a MOD
timeout.
The clear state of OUT can be set via the OUTP option
(Section 2.7.1).
L
Q
8
QT310/R1.03 21.09.03
相關PDF資料 |
PDF描述 |
|---|---|
| QT310-D | PROGRAMMABLE CAPACITANCE SENSOR IC |
| QT310-IS | PROGRAMMABLE CAPACITANCE SENSOR IC |
| QT320 | 2 CHANNEL PROGAMMABLE ADVANCED SENSOR IC |
| QT320-D | 2 CHANNEL PROGAMMABLE ADVANCED SENSOR IC |
| QT320-IS | 2 CHANNEL PROGAMMABLE ADVANCED SENSOR IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QT310-D | 制造商:Quantum Corp 功能描述:IC TOUCH SENSOR 1CH DIP8 310 |
| QT310-IS | 功能描述:SENSOR IC TOUCH PROG 1CH 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QProx™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| QT310-ISG | 制造商:Quantum Corp 功能描述:TOUCH SENSOR 1 CHAN SOIC8 310 ((NW)) |
| QT310-ISG SL775 | 制造商:Atmel Corporation 功能描述:TOUCH PRODUCT - Bulk |
| QT310-S | 功能描述:SENSOR IC TOUCH PROG 1CH 8-SOIC 制造商:microchip technology 系列:QProx?? 包裝:管件 零件狀態:停產 觸摸屏:2 線電容 分辨率（位）:16 b 接口:串行 電壓基準:內部 電壓 - 電源:1.8 V ~ 5 V 電流 - 電源:600μA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.209"，5.30mm 寬） 供應商器件封裝:8-SO 基本零件編號:QT310 標準包裝:95 |
發布緊急采購，3分鐘左右您將得到回復。