參數資料
型號： QT310
廠商： Electronic Theatre Controls, Inc.
英文描述： PROGRAMMABLE CAPACITANCE SENSOR IC
中文描述： 可編程電容傳感器IC
文件頁數： 11/20頁
文件大?。?/td> 837K
代理商： QT310
During fast integration (Section 2.5), when bursts are
generated quickly a number of times in sequence without
regard to the sleep timer, a single SYNC_O pulse is
generated only after the last burst in the series of fast spaced
bursts in order to prevent downstream slave parts from being
triggered too rapidly.
If SC=0 (no sleep cycles), no Sync_O pulses are generated.
Disabling Sync
: Connecting Sync_I to +Vdd will disable Sync
and the part will acquire bursts at the normal rate. If Sync is at
Vss, the device will wait for a Sync pulse, until the Tsc period
expires; at that point the part will acquire regardless of the
absence of a Sync pulse.
2.9.1 D
AISY
-C
HAINING
QT310’
S
One use for synchronization is where two or more QT310’s in
close proximity to each other are synchronously daisy-
chained to avoid crosstalk (Figure 2-3).
One QT310 should be designated as the ‘Master’; this part
should have the shortest SC sleep time, while the
downstream parts which depend on the master and any
intermediary devices should have longer sleep time settings
than the master.
The parts can be chained in a loop (Fig 2-4 switch set to
‘closed loop’); in this configuration the master will generate a
new burst after the last slave has finished, making the scan
sequence of all devices the most time-efficient possible. If the
master doesn’t received a pulse before the sleep time has
elapsed it will generate a new burst. This mode is most useful
if there are a relatively small number of devices in the chain
and there is a need for fast response.
In open-loop, the rep rate of acquisition is set purely by the
burst rate of the master. It is possible in this mode to have
very long chains of parts with relatively good response time.
The disadvantage of this mode is that it is possible for the
bursts of downstream slaves to overlap with upstream
devices, potentially causing interference if their electrodes are
in physical proximity to each other.
It is also possible to devise a tree structure of devices, where
some devices in the chain trigger two or more slaves. This
speeds up the acquisition process considerably, but some
thought must be given to timing considerations so that
adjacent electrodes do not have bursts which overlap each
other in time.
After the burst has completed the QT310 checks the level on
SYNC_I. If SYNC_I is high, the part goes back to sleep; if
SYNC_I is still low the device waits until the SYNC_I is high
again before going back to sleep. If this is the case, power
drain will be higher so it is important to limit the pulse width to
an amount less than the burst length (but greater than
>15μs).
2.9.2 N
OISE
S
YNCHRONIZATION
Using the sync feature, a QT310 can be synchronized to a
repetitive external source of interference such as the power
line frequency (Figure 2-4) in order to dramatically reduce
signal noise. If line frequency is present near the sensors, this
feature should be used.
With this circuit the sensor can tolerate up to 100V/M of AC
electric field. It is particularly useful for line-powered touch
controls.
Noise sync and daisy-chaining can be combined by having
the first device in the chain sync to the external noise source.
3 Circuit Guidelines
3.1 SAMPLE CAPACITORS
Cs capacitors can be virtually any plastic film or low to
medium-K ceramic capacitor. The normal usable Cs range is
from 10nF ~ 200nF depending
on the sensitivity required;
larger values of Cs require higher stability to ensure reliable
sensing. Acceptable capacitor types include NP0 or C0G
ceramic, PPS film, Polypropylene film, and X7R ceramic in
that order.
3.2 POWER SUPPLY
3.2.1 S
TABILITY
The QT310 derives its internal references from the power
supply. Sensitivity shifts and timing changes will occur with
changes in Vdd, as often happens when additional power
supply loads are switched on or off via the Out pin.
These supply shifts can induce detection ‘cycling’, whereby an
object is detected, the load is turned on, the supply sags, the
detection is no longer sensed, the load is turned off, the
supply rises and the object is reacquired,
ad infinitum
.
Detection ‘stiction’, the opposite effect, can occur if a load is
shed when the output is active and the signal swings are
small: the Out pin can remain stuck even if the detected
object is no longer near the electrode.
3.2.2 S
UPPLY
R
EQUIREMENTS
Vdd can range from 2.0 to 5.0 volts. If Setups programming is
required during operation, the minimum Vdd is 2.2V. Current
drain will vary depending on Vdd, the chosen sleep cycles,
and the burst lengths. Increasing Cx values will
decrease
power drain since increasing Cx loads decrease burst length
(Figures
5-1 and 5-2).
L
Q
11
QT310/R1.03 21.09.03
Figure 2-4 Line sync circuit
5
7
SNS2
VSS
8
VDD
2
1
3
SNS1
OUT
Vdd
6
Vdd
/SYNC_O
SENSOR
R1
1M
CS
OUT1
U1
4
/SYNC_I
/CAL
R4
4.7k - 10K
100pF
C1
2.2nF
C2
/SYNC_O
R3
1M
74HC14
U2:A
Line Input
4R2
相關PDF資料
PDF描述
QT310-D PROGRAMMABLE CAPACITANCE SENSOR IC
QT310-IS PROGRAMMABLE CAPACITANCE SENSOR IC
QT320 2 CHANNEL PROGAMMABLE ADVANCED SENSOR IC
QT320-D 2 CHANNEL PROGAMMABLE ADVANCED SENSOR IC
QT320-IS 2 CHANNEL PROGAMMABLE ADVANCED SENSOR IC
相關代理商/技術參數
參數描述
QT310-D 制造商:Quantum Corp 功能描述:IC TOUCH SENSOR 1CH DIP8 310
QT310-IS 功能描述:SENSOR IC TOUCH PROG 1CH 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QProx™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
QT310-ISG 制造商:Quantum Corp 功能描述:TOUCH SENSOR 1 CHAN SOIC8 310 ((NW))
QT310-ISG SL775 制造商:Atmel Corporation 功能描述:TOUCH PRODUCT - Bulk
QT310-S 功能描述:SENSOR IC TOUCH PROG 1CH 8-SOIC 制造商:microchip technology 系列:QProx?? 包裝:管件 零件狀態:停產 觸摸屏:2 線電容 分辨率（位）:16 b 接口:串行 電壓基準:內部 電壓 - 電源:1.8 V ~ 5 V 電流 - 電源:600μA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.209"，5.30mm 寬） 供應商器件封裝:8-SO 基本零件編號:QT310 標準包裝:95
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*