- 您現在的位置：買賣IC網 > PDF目錄361324 > QT110 (Electronic Theatre Controls, Inc.) SENSOR ICs PDF資料下載
參數資料
| 型號： | QT110 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | SENSOR ICs |
| 中文描述： | 傳感器IC |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 207K |
| 代理商： | QT110 |
1 - OVERVIEW
The QT110 is a digital burst mode charge-transfer (QT)
sensor designed specifically for touch controls; it includes all
hardware and signal processing functions necessary to
provide stable sensing under a wide variety of changing
conditions. Only a single low cost, non-critical capacitor is
required for operation.
Figure 1-1 shows the basic QT110 circuit using the device,
with a conventional output drive and power supply
connections. Figure 1-2 shows a second configuration using
a common power/signal rail which can be a long twisted pair
from a controller; this configuration uses the built-in pulse
mode to transmit output state to the host controller (QT110
only).
1.1 BASIC OPERATION
The QT110 employs short, ultra-low duty cycle bursts of
charge-transfer cycles to acquire its signal. Burst mode
permits power consumption in the low microamp range,
dramatically reduces RF emissions, lowers susceptibility to
EMI, and yet permits excellent response time. Internally the
signals are digitally processed to reject impulse noise, using
a 'consensus' filter which requires four consecutive
confirmations of a detection before the output is activated.
The QT switches and charge measurement hardware
functions are all internal to the QT110 (Figure 1-3). A 14-bit
single-slope switched capacitor ADC includes both the
required QT charge and transfer switches in a configuration
that provides direct ADC conversion. The ADC is designed to
dynamically optimize the QT burst length according to the
rate of charge buildup on Cs, which in turn depends on the
values of Cs, Cx, and Vdd. Vdd is used as the charge
reference voltage. Larger values of Cx cause the charge
transferred into Cs to rise more rapidly, reducing available
resolution; as a minimum resolution is required for proper
operation, this can result in dramatically reduced apparent
gain. Conversely, larger values of Cs reduce the rise of
differential voltage across it, increasing available resolution
by permitting longer QT bursts. The value of Cs can thus be
increased to allow larger values of Cx to be tolerated (Figures
4-1, 4-2, 4-3 in Specifications, rear).
The IC is highly tolerant of changes in Cs since it computes
the threshold level ratiometrically with respect to absolute
load, and does so dynamically at all times.
Cs is thus non-critical; as it drifts with temperature, the
threshold algorithm compensates for the drift automatically.
A simple circuit variation is to replace Cs with a bare piezo
sounder (Section 2), which is merely another type of
capacitor, albeit with a large thermal drift coefficient. If C
piezo
is in the proper range, no other external component is
required. If C
piezo
is too small, it can simply be ‘topped up’ with
an inexpensive ceramic capacitor connected in parallel with
it. The QT110 drives a 4kHz signal across SNS1 and SNS2
to make the piezo (if installed) sound a short tone for 75ms
immediately after detection, to act as an audible confirmation.
Option pins allow the selection or alteration of several special
features and sensitivity.
1.2 ELECTRODE DRIVE
The internal ADC treats Cs as a floating transfer capacitor; as
a direct result, the sense electrode can be connected to
either SNS1 or SNS2 with no performance difference. In both
cases the rule Cs >> Cx must be observed for proper
operation. The polarity of the charge buildup across Cs
during a burst is the same in either case.
It is possible to connect separate Cx and Cx’ loads to SNS1
and SNS2 simultaneously, although the result is no different
than if the loads were connected together at SNS1 (or
SNS2). It is important to limit the amount of stray capacitance
on both terminals, especially if the load Cx is already large,
for example by minimizing trace lengths
and widths so as not to exceed the Cx
load specification and to allow for a
larger sensing electrode size if so
desired.
SENSING
ELECTRODE
The PCB traces, wiring, and any
components associated with or in contact
with SNS1 and SNS2 will become touch
sensitive and should be treated with
caution to limit the touch area to the
desired
location.
electrodes can be used, for example to
create a control button on both sides of
an object, however it is impossible for the
sensor to distinguish between the two
touch areas.
Multiple
touch
- 2 -
Figure 1-1 Standard mode options
+2.5 to 5
SENSING
ELECTRODE
C
s
10nF
3
4
6
5
1
7
2
OUT
OPT1
OPT2
GAIN
SNS1
SNS2
Vss
Vdd
OUTPUT=DC
TIMEOUT=10 Secs
TOGGLE=OFF
GAIN=HIGH
C
x
8
Figure 1-2 2-wire operation, self-powered (QT110 only)
C
x
+
22μF10V AL
10nF
CMOS
GATE
+3V
2.2k
Twisted
pair
C
s
8
OUT
OPT1
OPT2
GAIN
SNS1
SNS2
Vss
Vdd
3
4
6
5
1
7
2
相關PDF資料 |
PDF描述 |
|---|---|
| QT110H | SENSOR ICs |
| QT113 | CHARGE-TRANSFER TOUCH SENSOR |
| QT113-D | CHARGE-TRANSFER TOUCH SENSOR |
| QT113-IS | CHARGE-TRANSFER TOUCH SENSOR |
| QT113-S | CHARGE-TRANSFER TOUCH SENSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QT110_05 | 制造商:QUANTUM 制造商全稱:QUANTUM 功能描述:QTOUCH⑩ SENSOR IC |
| QT1100A | 制造商:QUANTUM 制造商全稱:QUANTUM 功能描述:10 KEY QTOUCH SENSOR IC |
| QT1100A-IS | 功能描述:IC SENSOR 10CHAN QTOUCH 48SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QTouch™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| QT1100A-ISG | 功能描述:接口 - 專用 Integrated Circuit RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| QT1100-ISG | 功能描述:板機接口移動感應器和位置傳感器 INTEGRATED-CIRCUIT RoHS:否 制造商:Panasonic Electric Works 封裝 / 箱體:TO-5 感應距離:3 m 輸出類型:Digital 電源電壓-最大:6 V 電源電壓-最小:2.3 V 電源電流: 最大工作溫度:+ 60 C 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。