參數資料
型號： PSD834F2V
英文描述： Flash PSD, 3.3V Supply, for 8-bit MCUs 2 Mbit + 256 Kbit Dual Flash Memories and 64 Kbit SRAM(2M位+256K位雙路閃速存儲器和64K位靜態RAM,閃速PSD,3.3V電源,用于8位MCU.)
中文描述： 閃光私營部門，3.3V電源，為8位微控制器2兆256千位雙閃存和64千位的SRAM（200萬位256K位雙路閃速存儲器和64K的位靜態內存，閃速私營部門，3.3V的電源，用于8位微控制器。）
文件頁數： 61/89頁
文件大小： 522K
代理商： PSD834F2V
61/89
PSD834F2V
PROGRAMMING IN-CIRCUIT USING THE JTAG SERIAL INTERFACE
The JTAG Serial Interface block can be enabled
on Port C (see Table 33). All memory blocks (pri-
mary and secondary Flash memory), PLD logic,
and PSD Configuration Register bits may be pro-
grammed through the JTAG Serial Interface block.
A blank device can be mounted on a printed circuit
board and programmed using JTAG.
The standard JTAG signals (IEEE 1149.1) are
TMS, TCK, TDI, and TDO. Twoadditional signals,
TSTAT and TERR, are optional JTAG extensions
used to speed up Program and Erase cycles.
By default, on a blank PSD (as shipped from the
factory or after erasure), four pins on Port C are
enabled for the basic JTAG signals TMS, TCK,
TDI, and TDO.
See Application Note AN1153 for more details on
JTAG In-System Programming (ISP).
Standard JTAG Signals
The standard JTAG signals (TMS, TCK, TDI, and
TDO) canbe enabled by any of three different con-
ditions that are logically ORed. When enabled,
TDI, TDO, TCK, and TMS are inputs, waiting for a
JTAG serial command froman external JTAGcon-
troller device (such as FlashLINK or Automated
Test Equipment). When the enabling command is
received, TDO becomes an output and the JTAG
channel is fully functional inside the PSD. The
same command that enables the JTAG channel
may optionally enable thetwo additionalJTAG sig-
nals, TSTAT and TERR.
The following symbolic logic equationspecifies the
conditions enabling the four basic JTAG signals
(TMS, TCK, TDI, and TDO) on their respective
Port C pins. For purposes of discussion, the logic
label JTAG_ON is used. When JTAG_ON is true,
the four pins are enabled for JTAG. When
JTAG_ON is false, the four pins can be used for
general PSD I/O.
JTAG_ON = PSDsoft_enabled +
/* An NVM configuration bit inside the
PSD
is
set
by
the
designer
PSDsoft Express Configuration utility.
This dedicates the pins for JTAG at all
times (compliant with IEEE 1149.1 */
Microcontroller_enabled
+
/* The microcontroller can set a bit at
run-time
by
writing
to
register,
JTAG
Enable.
This register
is located at address CSIOP + offset
C7h.
Setting
the
JTAG_ENABLE
this register will enable the pins for
JTAG use. This bit is cleared by a PSD
reset
or
the
microcontroller.
Table 34 for bit definition. */
PSD_product_term_enabled;
/* A dedicated product term (PT) inside
the PSD can be used to enable the JTAG
pins.
This
PT
has
the
reserved
JTAGSEL.
Once
defined
as
PSDabel,
the
designer
can
in
the
the
PSD
bit
in
See
name
a
node
write
in
an
equation
used
multiplexed with other I/O signals. It
is
recommended
to
node JTAGSEL to the JEN\ signal on the
Flashlink cable when multiplexing JTAG
signals. See Application Note 1153 for
details. */
The state of the PSD Reset (RESET) signal does
not interrupt (or prevent) JTAG operations if the
JTAG pins are dedicated by an NVM configuration
bit (via PSDsoft Express). However, Reset (RE-
SET) will prevent or interrupt JTAG operations if
the JTAG enable register is used to enable the
JTAG pins.
The PSD supports JTAG In-System-Configuration
(ISC) commands,butnot Boundary Scan.The PS-
Dsoft Express software tool and FlashLINK JTAG
programming cable implement the JTAG In-Sys-
tem-Configuration (ISC) commands. A definition
of these JTAG In-System-Configuration (ISC)
commands and sequences is defined in a supple-
mental document available from ST. This docu-
ment is needed only as a reference for designers
who use a FlashLINK to program their PSD.
for JTAGSEL.
when
the
This method is
JTAG
pins
Port
C
are
logically
tie
the
Table 33. JTAG Port Signals
JTAG Extensions
TSTAT and TERR aretwoJTAG extension signals
enabled by an “ISC_ENABLE” command received
over the four standard JTAG signals (TMS, TCK,
TDI, and TDO). They are used to speed Program
and Erase cycles by indicating status on PSD sig-
nals instead of having to scan the status out seri-
ally using the standard JTAG channel. See
Application Note AN1153
TERR indicates if an error has occurred when
erasing a sector or programming a byte in Flash
memory. This signal goes Low (active) when an
Error condition occurs, and stays Low until an
“ISC_CLEAR” command is executed or a chip Re-
set
(RESET)
pulse
“ISC_DISABLE” command.
TSTAT behaves the same as Ready/Busy de-
scribed inthe section entitled“Ready/Busy (PC3)”,
on page 15. TSTAT is High when the PSD device
is
received
after
an
Port C Pin
JTAG Signals
Description
PC0
TMS
Mode Select
PC1
TCK
Clock
PC3
TSTAT
Status
PC4
TERR
Error Flag
PC5
TDI
Serial Data In
PC6
TDO
Serial Data Out
相關PDF資料
PDF描述
PSD834F2 Flash In-System Programmable (ISP) Peripherals For 8-bit MCUs(用于8位MCUs的閃速ISP外圍)
PSD835G2 Configurable Memory System on a Chip for 8-Bit Microcontrollers(8位微控制器片上存儲器可編程外設)
PSD835G2 100V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a TO-254AA Tabless package; Similar to IRHMJ57160 with optional Total Dose Rating of 1000kRads
PSD835G2V 150V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a SMD-2 package. Also available with 300 kRads Total Dose Rating.; Similar to IRHNA67164 with optional Total Dose Rating of 300 kRads.
PSD835G2-B-12B81 Configurable Memory System on a Chip for 8-Bit Microcontrollers
相關代理商/技術參數
參數描述
PSD834F2V-15J 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 150ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD834F2V-15M 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 150ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD834F2V-20JI 功能描述:CPLD - 復雜可編程邏輯器件 3.0V 2M 200ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
PSD834F2V-20MI 功能描述:SPLD - 簡單可編程邏輯器件 3.0V 2M 200ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD835G2-70U 功能描述:靜態隨機存取存儲器 5.0V 4M 70ns RoHS:否 制造商:Cypress Semiconductor 存儲容量:16 Mbit 組織:1 M x 16 訪問時間:55 ns 電源電壓-最大:3.6 V 電源電壓-最小:2.2 V 最大工作電流:22 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TSOP-48 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*