- 您現在的位置：買賣IC網 > PDF目錄368164 > PSD4135F3-C-70B81I (意法半導體) Flash In-System-Programmable Peripherals for 16-Bit MCUs PDF資料下載
參數資料
| 型號： | PSD4135F3-C-70B81I |
| 廠商： | 意法半導體 |
| 英文描述： | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| 中文描述： | Flash在系統可編程外設的16位微控制器 |
| 文件頁數： | 20/93頁 |
| 文件大?。?/td> | 503K |
| 代理商： | PSD4135F3-C-70B81I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁
Preliminary Information
PSD4000 Series
17
FS0-7
or
CSBOOT0-3
Instruction
(Note 14)
Cycle 1 Cycle 2 Cycle 3
Cycle 4
Cycle5
Cycle 6
Cycle 7
Read (Note 5)
1
“Read”
RA RD
Read Main Flash ID
(Note 6)
AAh
55h
90h
“Read”
ID
@XX02h
@XAAAh @X554h @XAAAh
Read Sector Protection
(Notes 6,8,13)
1
AAh
55h
90h
“Read”
@XAAAh @X554h @XAAAh 00h or 01h
@XX04h
Program a Flash Word
1
AAh
55h
A0h
PD@PA
@XAAAh @X554h @XAAAh
Erase One Flash Sector
1
AAh
55h
80h
AAh
55h
30h
@SA
30h
@XAAAh @X554h @XAAAh
@XAAAh
@X554h
@next SA
(Note 7)
Erase Flash Block
(Bulk Erase)
1
AAh
55h
80h
AAh
55h
10h
@XAAAh @X554h @XAAAh
@XAAAh
@X554h
@XAAAh
Suspend Sector Erase
(Note 11)
1
B0h
@xxxh
Resume Sector Erase
(Note 12)
1
30h
@xxxh
Reset (Note 6)
1
F0 @ any
address
Unlock Bypass
1
AAh
55h
20h
@XAAAh @X554h @XAAAh
Unlock Bypass Program
(Note 9)
1
A0h
PD@PA
@XXXXh
Unlock Bypass Reset
(Note 10)
1
90h
00h
@XXXXh @XXXXh
Table 8. Instructions
X
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of the WR#
(CNTL0) pulse. PA is an even address for PSD in word programming mode.
PD = Data (word) to be programmed at location PA. Data is latched on the rising edge of WR# (CNTL0) pulse.
SA = Address of the sector to be erased or verified. The chip select (FS0-7 or CSBOOT0-3) of the sector to be
erased must be active (high).
= Don’t Care. “xxxh” address in the above table must be an even address.
NOTES:
1.
All bus cycles are write bus cycle except the ones with the “read” label.
2.
All values are in hexadecimal.
3.
FS0-7 and CSBOOT0-3 are active high and are defined in PSDsoft.
4.
Only Address bits A11-A0 are used in Instruction decoding.
5.
No unlock or command cycles required when device is in read mode.
6.
The Reset command is required to return to the read mode after reading the Flash ID, Sector Protect status
or if DQ5 (DQ13) goes high.
7.
Additional sectors to be erased must be entered within 80μs.
8.
The data is 00h for an unprotected sector and 01h for a protected sector. In the fourth cycle, the sector chip
select is active and (A1 = 1, A0 = 0).
9.
The Unlock Bypass command is required prior to the Unlock Bypass Program command.
10. The Unlock Bypass Reset command is required to return to reading array data when the device is in the
Unlock Bypass mode.
11. The system may read and program functions in non-erasing sectors, read the Flash ID or read the Sector
Protect status, when in the Erase Suspend mode. The erase Suspend command is valid only during a sector
erase operation.
12. The Erase Resume command is valid only during the Erase Suspend mode.
13. The MCU cannot invoke these instructions while executing code from the same Flash memory for which the
instruction is intended. The MCU must fetch, for example, codes from the Secondary Flash memory when
reading the Sector Protection Status of the main Flash.
14. All write bus cycles in an instruction are byte write to even address (XA4Ah or X554h). Flash Programming
bys cycle is writing a word to even address.
The
PSD4000
Functional
Blocks
(cont.)
相關PDF資料 |
PDF描述 |
|---|---|
| PSD4135F3-C-70J | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135F3-C-70JI | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135F3-C-70M | Ceramic Chip Capacitors / Standard C0G; Capacitance [nom]: 680pF; Working Voltage (Vdc)[max]: 200V; Capacitance Tolerance: +/-20%; Dielectric: Multilayer Ceramic; Temperature Coefficient: C0G (NP0); Lead Style: Surface Mount Chip; Lead Dimensions: 1210; Termination: Tin Plated Nickel Barrier; Body Dimensions: 0.126" x 0.098"; Container: Bulk; Features: Unmarked |
| PSD4135F3-C-70MI | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135F3-C-70U | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD4135F3-C-70J | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135F3-C-70JI | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135F3-C-70M | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135F3-C-70MI | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135F3-C-70U | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs |
發布緊急采購，3分鐘左右您將得到回復。