參數資料
型號： PSD403A2-C-15L
廠商： 意法半導體
英文描述： RECTIFIER FAST-RECOVERY SINGLE 1A 200V 40A-ifsm 0.875V-vf 25ns 2uA-ir SMB 5K/REEL-13
中文描述： 低成本現場可編程微控制器外圍設備
文件頁數： 51/123頁
文件大?。?/td> 657K
代理商： PSD403A2-C-15L
PSD4XX Famly
48
9.3 I/OPorts
There are 5 programmable 8-bit I/O ports: Port A, Port B, Port C, Port D and Port E. These
ports all have multiple operating modes, depending on the configuration. Some of the basic
functions are providing input/output for the ZPLD, or can be used for standard I/O. Each
port pin is individually configurable, thus enabling a single 8-bit port to perform multiple
functions. The I/O ports occupy 256 bytes of memory space as defined by “CSIOP”. Refer
to the System Configuration section for I/O register address offset.
To set up the port configuration the user is required to:
1. Define I/O Port Chip Select (CSIOP) in the ABEL file.
2. Initialize certain port configuration registers in the user’s program and/or
3. Specify the configuration in the PSD4XX PSDsoft Software.
4. Unused input pins should be tied to V
CC
or GND.
The following is a description of the operating modes of the I/O ports. The functions of the
port registers are described in later sections.
9.3.1 Standard MCUI/O
The Standard MCU I/O Mode provides additional I/O capability to the microcontroller. In this
mode, the ports can perform standard I/O functions such as sensing or controlling various
external I/O devices. Operation options of this mode are as follows:
J
Configuration
1.Declare pins or signals which are used as I/O in the ABEL file.
2.Set the bit or bits in the Control Register to "1".
3.
As Output Port
– Write output data to Data Out Register
– Set Direction Register to output mode
4.
As Input Port
– Set Direction Register to input mode
– Read input from Data In Register
The port remains an output or input port as long as the Direction Register is not changed.
9.3.2 PLDI/O
The PLD I/O mode enables the port to be configured as an input to the ZPLD, or as an
output from the GPLD macrocell. The output can be tri-stated with a control signal defined
by a product term from the ZPLD. This mode is configured by the user in the PSD4XX
PSDsoft Software, and is enabled upon power up. For a detailed description, see the
section on the ZPLD.
J
Configuration
1.Declare pins or signals in the ABEL file (PSDsoft).
2.Write logic equations in the ABEL file.
3.PSD Compiler maps the PLD functions to the PSD.
The PSD4XX
Architecture
(cont.)
相關PDF資料
PDF描述
PSD413A2-C-15L RECTIFIER FAST-RECOVERY SINGLE 1A 400V 35A-ifsm 1.25V-vf 50ns 5uA-ir SMB 5K/REEL-13
PSD403A2-C-15U RECTIFIER FAST-RECOVERY SINGLE 1A 600V 35A-ifsm 1.25V-vf 50ns 5uA-ir SMB 5K/REEL-13
PSD413A2-C-15U Low Cost Field Programmable Microcontroller Peripherals
PSD403A2-C-70J TVS BI-DIR 100V 600W DO-15
PSD413A2-C-70J TVS BI-DIR 10V 600W DO-15
相關代理商/技術參數
參數描述
PSD403A2-C-15U 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD403A2-C-70J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD403A2-C-70L 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD403A2-C-70U 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD403A2-C-90JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*