- 您現在的位置：買賣IC網 > PDF目錄96788 > PS21562-P AC MOTOR CONTROLLER, 10 A, DMA35 PDF資料下載
參數資料
| 型號： | PS21562-P |
| 元件分類： | 運動控制電子 |
| 英文描述： | AC MOTOR CONTROLLER, 10 A, DMA35 |
| 封裝： | LEAD FREE, DIP-35 |
| 文件頁數： | 9/9頁 |
| 文件大?。?/td> | 131K |
| 代理商： | PS21562-P |
MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module>
PS21562-P
TRANSFER-MOLD TYPE
INSULATED TYPE
Sep. 2005
Fig. 8 TYPICAL DIP-IPM APPLICATION CIRCUIT EXAMPLE
Note 1 : To prevent the input signals oscillation, the wiring of each input should be as short as possible. (Less than 2cm)
2: By virtue of integrating an application specific type HVIC inside the module, direct coupling to MCU terminals without any opto-coupler
or transformer isolation is possible.
3: FO output is open drain type. This signal line should be pulled up to the positive side of the 5V power supply with approximately 10k
resistor.
4: FO output pulse width is determined by the external capacitor between CFO and VNC terminals (CFO). (Example : CFO = 22 nF
→ tFO
= 1.8 ms (typ.))
5: The logic of input signal is high-active. The DIP-IPM input signal section integrates a 2.5k
(min) pull-down resistor. Therefore, when
using external filtering resistor, care must be taken to satisfy the turn-on threshold voltage requirement.
6: To prevent malfunction of protection, the wiring of A, B, C should be as short as possible.
7: Please set the C5R1 time constant in the range 1.5~2
s.
8: Each capacitor should be located as nearby the pins of the DIP-IPM as possible.
9: To prevent surge destruction, the wiring between the smoothing capacitor and the P, N1 pins should be as short as possible. Approxi-
mately a 0.1~0.22
F snubber capacitor between the P-N1 pins is recommended.
10 : The terminal VNO should be connected with the terminal N outside.
11 : To prevent ICs from surge destruction, it is recommended to insert a Zener diode (24V, 1W) nearby each pair of supply terminals.
HO
DIP-IPM
C3
C2
C1
HO
IN
COM
UOUT
VOUT
WOUT
VNO
CFO
GND
F
o
WN
VN
VCC
C
B
A
C4(CFO)
CFO
R1
N1
C5
CIN
N
W
V
U
P
VS
VB
VCC
Fo
WN
VN
UN
UN
WP
VP
UP
VNC
VN1
VP1
VWFS
VVFS
VUFS
VWFB
VVFB
VUFB
M
C3
HVIC1
HVIC2
HVIC3
LVIC
VNO
15V line
Long GND wiring here might generate
noise to input and cause IGBT
malfunction.
resistor
If this wiring is too long, the SC level
fluctuation might be larger and cause
SC malfunction.
Too long wiring here might
cause short-circuit.
Shunt
CONTROLLER
5V line
C1:Tight tolerance temp-compensated electrolytic type
C2,C3: 0.22~2
F R-category ceramic capacitor for noise filtering.
相關PDF資料 |
PDF描述 |
|---|---|
| PS21562-SP | AC MOTOR CONTROLLER, 10 A, XMA37 |
| PS21563 | AC MOTOR CONTROLLER, 20 A, XMA35 |
| PS21564-SP | AC MOTOR CONTROLLER, 30 A, DMA37 |
| PS21564-S | AC MOTOR CONTROLLER, 30 A, XMA37 |
| PS21864 | AC MOTOR CONTROLLER, 30 A, QMA41 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PS21562-SP | 功能描述:MOD IPM 600V 5A MINI DIP RoHS:是 類別:半導體模塊 >> 功率驅動器 系列:Intellimod™ 標準包裝:15 系列:SPM® 類型:FET 配置:三相反相器 電流:1.8A 電壓:500V 電壓 - 隔離:1500Vrms 封裝/外殼:23-DIP 模塊 |
| PS21563 | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Intellimod⑩ Module Dual-In-Line Intelligent Power Module (10 Amperes/600 Volts) |
| PS21563-P | 功能描述:MOD IPM 600V 10A MINI DIP RoHS:是 類別:半導體模塊 >> 功率驅動器 系列:Intellimod™ 標準包裝:15 系列:SPM® 類型:FET 配置:三相反相器 電流:1.8A 電壓:500V 電壓 - 隔離:1500Vrms 封裝/外殼:23-DIP 模塊 |
| PS21563-PP | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Intellimod? Module Dual-In-Line Intelligent Power Module 10 Amperes/600 Volts |
| PS21563-SP | 功能描述:MOD IPM 600V 10A MINI DIP RoHS:是 類別:半導體模塊 >> 功率驅動器 系列:Intellimod™ 標準包裝:15 系列:SPM® 類型:FET 配置:三相反相器 電流:1.8A 電壓:500V 電壓 - 隔離:1500Vrms 封裝/外殼:23-DIP 模塊 |
發布緊急采購，3分鐘左右您將得到回復。