- 您現在的位置：買賣IC網 > PDF目錄96788 > PS21562-P AC MOTOR CONTROLLER, 10 A, DMA35 PDF資料下載
參數資料
| 型號： | PS21562-P |
| 元件分類： | 運動控制電子 |
| 英文描述： | AC MOTOR CONTROLLER, 10 A, DMA35 |
| 封裝： | LEAD FREE, DIP-35 |
| 文件頁數： | 2/9頁 |
| 文件大?。?/td> | 131K |
| 代理商： | PS21562-P |
MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module>
PS21562-P
TRANSFER-MOLD TYPE
INSULATED TYPE
Sep. 2005
Note1: In the recommended external protection circuit, please select the RC time constant in the range 1.5~2.0
s.
2: To prevent erroneous protection operation, the wiring of A, B, C should be as short as possible.
Drive circuit
Protection circuit
W
V
U
B
C
VNC
CIN
A
P
N1
N
C
R
Shunt Resistor
External protection circuit
DIP-IPM
L-side IGBTS
H-side IGBTS
SC Protection
Trip Level
IC (A)
tw (
s)
2
0
Short Circuit Protective Function (SC) :
SC protection is achieved by sensing the L-side DC-Bus current (through the external
shunt resistor) after allowing a suitable filtering time (defined by the RC circuit).
When the sensed shunt voltage exceeds the SC trip-level, all the L-side IGBTs are turned
OFF and a fault signal (Fo) is output. Since the SC fault may be repetitive, it is
recommended to stop the system when the Fo signal is received and check the fault.
Collector current
waveform
(Note 1)
(Note 2)
AC line input
Drive circuit
CBU–
CBU+
CBV–
CBV+
CBW–
CBW+
(15V line)
(3, 5V line) (Note 1, 2)
VD
VNC
W
V
U
Input signal
conditioning
Level shifter
Drive circuit
Protection
circuit (UV)
Input signal
conditioning
Input signal
conditioning
Input signal conditioning
Fo logic
Protection
circuit
circuit (UV)
Protection
circuit (UV)
Control supply
Under-Voltage
protection
Drive circuit Drive circuit
FO
CFO
N1
Fault output (5V line)
(Note 3, 5)
High-side input (PWM)
(3, 5V line) (Note 1,2)
Low-side input (PWM)
(Note 6)
DIP-IPM
Z : ZNR (Surge absorber)
C : AC filter (Ceramic capacitor 2.2~6.5nF)
(Note : Additionally, an appropriate line-to line
surge absorber circuit may become necessary
depending on the application environment).
C2
C1
C1 : Tight tolerance, temp-compensated electrolytic type
C2 : 0.22~2
F R-category ceramic capacitor for noise filtering.
(Note : The capacitance value depends on the PWM control
scheme used in the applied system).
Note1:
Input logic is high-active. There is a 2.5k
(min) pull-down resistor built-in each input circuit. When using an external CR filter, please make it satisfy the
input threshold voltage.
2:
By virtue of integrating an application specific type HVIC inside the module, direct coupling to MCU terminals without any opto-coupler or transformer
isolation is possible. (see also Fig. 8)
3:
This output is open drain type. The signal line should be pulled up to the positive side of the 5V power supply with approximately 10k
resistance.
(see also Fig. 8)
4:
The wiring between the power DC link capacitor and the P, N1 terminals should be as short as possible to protect the DIP-IPM against catastrophic high
surge voltages. For extra precaution, a small film type snubber capacitor (0.1~0.22
F, high voltage type) is recommended to be mounted close to
these P-N1 DC power input pins.
5:
Fo output pulse width should be decided by putting external capacitor between CFO and VNC terminals. (Example : CFO=22nF
→ tFO=1.8ms (Typ.))
6:
High voltage (600V or more) and fast recovery type (less than 100ns) diodes should be used in the bootstrap circuit.
7:
The terminal VNO should be connected to the terminal N outside of DIP-IPM.
8:
To prevent ICs from surge destruction, it is recommended to insert a Zener diode (24V, 1W) nearby each pair of supply terminals.
H-side IGBTS
L-side IGBTS
(Note 4)
Fig. 3
Inrush current
limiter circuit
Level shifter Level shifter
Protection
AC line output
M
(Note 8)
Z
C
P
N
(Note 7)
CIN
VNO
Fig. 2 INTERNAL FUNCTIONS BLOCK DIAGRAM (TYPICAL APPLICATION EXAMPLE)
Fig. 3 EXTERNAL PART OF THE DIP-IPM PROTECTION CIRCUIT
相關PDF資料 |
PDF描述 |
|---|---|
| PS21562-SP | AC MOTOR CONTROLLER, 10 A, XMA37 |
| PS21563 | AC MOTOR CONTROLLER, 20 A, XMA35 |
| PS21564-SP | AC MOTOR CONTROLLER, 30 A, DMA37 |
| PS21564-S | AC MOTOR CONTROLLER, 30 A, XMA37 |
| PS21864 | AC MOTOR CONTROLLER, 30 A, QMA41 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PS21562-SP | 功能描述:MOD IPM 600V 5A MINI DIP RoHS:是 類別:半導體模塊 >> 功率驅動器 系列:Intellimod™ 標準包裝:15 系列:SPM® 類型:FET 配置:三相反相器 電流:1.8A 電壓:500V 電壓 - 隔離:1500Vrms 封裝/外殼:23-DIP 模塊 |
| PS21563 | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Intellimod⑩ Module Dual-In-Line Intelligent Power Module (10 Amperes/600 Volts) |
| PS21563-P | 功能描述:MOD IPM 600V 10A MINI DIP RoHS:是 類別:半導體模塊 >> 功率驅動器 系列:Intellimod™ 標準包裝:15 系列:SPM® 類型:FET 配置:三相反相器 電流:1.8A 電壓:500V 電壓 - 隔離:1500Vrms 封裝/外殼:23-DIP 模塊 |
| PS21563-PP | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Intellimod? Module Dual-In-Line Intelligent Power Module 10 Amperes/600 Volts |
| PS21563-SP | 功能描述:MOD IPM 600V 10A MINI DIP RoHS:是 類別:半導體模塊 >> 功率驅動器 系列:Intellimod™ 標準包裝:15 系列:SPM® 類型:FET 配置:三相反相器 電流:1.8A 電壓:500V 電壓 - 隔離:1500Vrms 封裝/外殼:23-DIP 模塊 |
發布緊急采購，3分鐘左右您將得到回復。