- 您現在的位置：買賣IC網 > PDF目錄368111 > PR31700 (NXP SEMICONDUCTORS) 32-bit RISC Microprocessor(32位 RISC微處理器) PDF資料下載
參數資料
| 型號： | PR31700 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-bit RISC Microprocessor(32位 RISC微處理器) |
| 中文描述： | 32-BIT, 75 MHz, RISC PROCESSOR, PQFP208 |
| 封裝： | PLASTIC, LQFP-208 |
| 文件頁數： | 9/36頁 |
| 文件大?。?/td> | 378K |
| 代理商： | PR31700 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Philips Semiconductors
Preliminary specification
PR31700
32-bit RISC microprocessor
1998 May 13
9
NAME
I/O
FUNCTIONS
Bus Arbitration Pins
DREQ*
I
This pin is used to request external arbitration. If the TESTSIU signal is high and the TESTSIU function has
been enabled, then once /DGRNT* is asserted, external logic can initiate reads or writes to PR31700
processor registers by driving the appropriate input signals. If the TESTSIU signal is low or the TESTSIU
function has not been enabled, then PR31700 memory transactions are halted and certain memory signals
will be tri-stated when /DGRNT* is asserted in order to allow an external master to access memory.
DGRNT*
O
This pin is asserted in response to /DREQ* to inform the external test logic or bus master that it can now
begin to drive signals.
*Active-low signal
NAME
I/O
FUNCTIONS
Clock Pins
SYSCLKIN
I
This pin should be connected along with SYSCLKOUT to an external crystal which is the main PR31700
clock source.
SYSCLKOUT
O
This pin should be connected along with SYSCLKIN to an external crystal which is the main PR31700 clock
source.
C32KIN
I
This pin along with C32KOUT should be connected to a 32.768 KHz crystal.
C32KOUT
O
This pin along with C32KIN should be connected to a 32.768 KHz crystal.
BC32K
O
This pin is a buffered output of the 32.768 KHz clock.
NAME
I/O
FUNCTIONS
CHI Pins
CHIFS
I/O
This pin is the CHI frame synchronization signal. This pin is available for use in one of two modes. As an
output, this pin allows PR31700 to be the master CHI sync source. As an input, this pin allows an external
peripheral to be the master CHI sync source and the PR31700 CHI module will slave to this external sync.
CHICLK
I/O
This pin is the CHI clock signal. This pin is available for use in one of two modes. As an output, this pin
allows PR31700 to be the master CHI clock source. As an input, this pin allows an external peripheral to be
the master CHI clock source and the PR31700 CHI module will slave to this external clock.
CHIDOUT
O
This pin is the CHI serial data output signal.
CHIDIN
I
This pin is the CHI serial data input signal.
NAME
I/O
FUNCTIONS
IO Pins
IO(6:0)
I/O
These pins are general purpose input/output ports. Each port can be independently programmed as an
input or output port. Each port can generate a separate positive and negative edge interrupt. Each port
can also be independently programmed to use a 16 to 24 msec debouncer.
MIO(1:0)
I/O
These pins are multi-function input/output ports. Each port can be independently programmed as an input
or output port, or can be programmed for multi-function use to support test signals (for debugging purposes
only). Each port can generate a separate positive and negative edge interrupt. Note that 30 other
multi-function pins are available for usage as multi-function input/output ports. These pins are named after
their respective standard/normal function and are not listed here.
NAME
I/O
FUNCTIONS
Reset Pins
/CPURES*
I
This pin is used to reset the CPU core. This pin should be connected to a switch for initiating a reset in the
event that a software problem might hang the CPU core. The pin should also be pulled up to VSTANDBY*
through an external pull-up resistor.
/PON*
I
This pin serves as the Power On Reset signal for PR31700. This signal must remain low when VSTANDBY
is asserted until VSTANDBY is stable. Once VSTANDBY is asserted, this signal should never go low
unless all power is lost in the system.
VSTANDBY—This signal provides power for the PR31700 and other components in the system that must never lose power. This signal should
always be asserted if there is eithr a good Main Backup Battery, or if a Battery Charger is plugged in.
相關PDF資料 |
PDF描述 |
|---|---|
| PR31MA11NTZ | Solid State Relay |
| PR3200 | DIFFERENTIAL PRESSURE TRANSMITTER |
| PR3400-33SF172M | Microprocessor |
| PR3400-33SG175B | 32-Bit Microprocessor |
| PR3400-33SG175C | 32-Bit Microprocessor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PR-318 | 制造商:Skylink 功能描述:Wireless HomeControl Plug-In On/Off Dimmer Receiver 制造商:SKYLINK 功能描述:PLUG IN ON/OFF DIMMER RECEIVERINTERNAL REPEATER |
| PR31HD22NSZ | 功能描述:RELAY SSR 240VAC 1.5A ZC 16-DIP RoHS:否 類別:繼電器 >> 固態 系列:PR31HD 其它有關文件:AQx REACH Cert of Compliance 特色產品:AQY Series Relays 標準包裝:1 系列:PhotoMOS™ AQY 電路:SPST-NO（1 Form A） 輸出類型:AC，DC（RF） 導通狀態電阻:1.25 歐姆 負載電流:250mA 輸入電壓:1.3VDC 電壓 - 負載:0 ~ 40 V 安裝類型:表面貼裝 端接類型:SMD（SMT）接片 封裝/外殼:4-SMD（0.175"，4.45mm） 供應商設備封裝:4-SSOP 包裝:Digi-Reel® 繼電器類型:繼電器 其它名稱:255-2683-6 |
| PR31HD22NSZF | 功能描述:固態繼電器-PCB安裝 16-DIP ZC 5mA T/H RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| PR31MA11NTZ | 功能描述:RELAY SSR 240VAC .06A TRIAC 6DIP RoHS:否 類別:繼電器 >> 固態 系列:PR31MA 其它有關文件:AQx REACH Cert of Compliance 特色產品:AQY Series Relays 標準包裝:1 系列:PhotoMOS™ AQY 電路:SPST-NO（1 Form A） 輸出類型:AC，DC（RF） 導通狀態電阻:1.25 歐姆 負載電流:250mA 輸入電壓:1.3VDC 電壓 - 負載:0 ~ 40 V 安裝類型:表面貼裝 端接類型:SMD（SMT）接片 封裝/外殼:4-SMD（0.175"，4.45mm） 供應商設備封裝:4-SSOP 包裝:Digi-Reel® 繼電器類型:繼電器 其它名稱:255-2683-6 |
| PR31MA11NTZF | 功能描述:固態繼電器-PCB安裝 6-DIP NON-ZC 10mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。