- 您現在的位置：買賣IC網 > PDF目錄359865 > PPC403GC-JA40C1 32-Bit Microprocessor PDF資料下載
參數資料
| 型號： | PPC403GC-JA40C1 |
| 元件分類： | 32位微控制器 |
| 英文描述： | 32-Bit Microprocessor |
| 中文描述： | 32位微處理器 |
| 文件頁數： | 9/48頁 |
| 文件大?。?/td> | 768K |
| 代理商： | PPC403GC-JA40C1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
IBM PowerPC 403GC
9
A29
119 C13
I/O
Address Bus Bit 29. See description of A22.
AMuxCAS
139 A8
O
DRAM External Address Multiplexer Select. AMuxCAS controls the
select logic on an external multiplexer. If AMuxCAS is low, the multi-
plexer should select the row address for the DRAM and when AMux-
CAS is 1, the multiplexer should select the column address.
BootW
11
E1
I
Boot-up ROM Width Select. BootW is sampled while the Reset pin is
active and again after Reset becomes inactive to determine the
width of the boot-up ROM. If this pin is tied to logic 0 when sampled
on reset, an 8-bit boot width is assumed. If BootW is tied to 1, a 32-
bit boot width is assumed. For 16-bit boot widths, this pin should be
tied to the RESET pin.
BusError
12
E3
I
Bus Error Input. A logic 0 input to the BusError pin by an external
device signals to the 403GC that an error occurred on the bus trans-
action. BusError is only sampled during the data transfer cycle or the
last wait cycle of the transfer.
BusReq/
DMADXFER
135 A9
O
Bus Request. While HoldAck is active, BusReq is active when the
403GC has a bus operation pending and needs to regain control of
the bus.
DMA Data Transfer. When HoldAck is not active, DMADXFER indi-
cates a valid data transfer cycle. For DMA use, DMADXFER controls
burst-mode fly-by DMA transfers between memory and peripherals.
DMADXFER is not meaningful unless a DMA Acknowledge signal
(DMAA0:3) is active. For transfer rates slower than one transfer per
cycle, DMADXFER is active for one cycle when one transfer is com-
plete and the next one starts. For transfer rates of one transfer per
cycle, DMADXFER remains active throughout the transfer.
CAS0
142 C8
O
DRAM Column Address Select 0. CAS0 is used with byte 0 of all
DRAM banks.
CAS1
143 A7
O
DRAM Column Address Select 1. CAS1 is used with byte 1 of all
DRAM banks.
CAS2
144 B7
O
DRAM Column Address Select 2. CAS2 is used with byte 2 of all
DRAM banks.
CAS3
145 D7
O
DRAM Column Address Select 3. CAS3 is used with byte 3 of all
DRAM banks.
CINT
36
L2
I
Critical Interrupt. To initiate a critical interrupt, the user must main-
tain a logic 0 on the CINT pin for a minimum of one SysClk clock
cycle followed by a logic 1 on the CINT pin for at least one SysClk
cycle.
CS0
155 C4
O
SRAM Chip Select 0. Bank register 0 controls an SRAM bank, CS0
is the chip select for that bank.
CS1
154 A4
O
SRAM Chip Select 1. See description of CS0 but controls bank 1.
Table 4. 403GC Signal Descriptions
Signal
Name
Pin
Ball
I/O
Type
Function
相關PDF資料 |
PDF描述 |
|---|---|
| 403G | Standard LED Lamp |
| 403HR | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 403Y | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 403 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 4040-11M | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PPC403GCX3JC66C2 | 制造商:IBM 功能描述:* |
| PPC403GCX-JA50C2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:32-Bit Microprocessor |
| PPC403GCX-JA60C2 | 制造商:IBM 功能描述:403GCX-JA60C2 |
| PPC403GCX-JA66C2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:32-Bit Microprocessor |
| PPC403GCX-JA66C2A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:32-Bit Microprocessor |
發布緊急采購，3分鐘左右您將得到回復。