- 您現在的位置：買賣IC網 > PDF目錄98052 > PIP8000FHN/N1 (NXP SEMICONDUCTORS) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC28 PDF資料下載
參數資料
| 型號： | PIP8000FHN/N1 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC28 |
| 封裝： | 6 X 6 MM, 0.85 MM HEIGHT, PLASTIC, MO-220, SOT788-1, HVQFN-28 |
| 文件頁數： | 5/26頁 |
| 文件大?。?/td> | 126K |
| 代理商： | PIP8000FHN/N1 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
PIP8000FHN_2
NXP B.V. 2009. All rights reserved.
Preliminary data sheet
Rev. 02 — 6 July 2009
13 of 26
NXP Semiconductors
PIP8000FHN
Digital power supervisor
10. PMBus
10.1 Introduction
The PIP8000FHN supports the PMBus Power System Management Protocol
Specications, revision 1.1. In Table 11 below all supported commands are marked grey.
Table 11 shows all supported commands including PIP8000FHN manufacturer specic
commands.
The fan monitor counts the LOW to HIGH transitions from the fan tachometer. There are
two fan inputs. The fan tachometer must produce a voltage swing with a LOW below
0.75 V and a HIGH above 2.5 V. The peak transition should be limited to 3.3 V to protect
the PIP8000FHN measurement inputs.
10.2 Non-volatile memory
The PIP8000FHN has on board non-volatile memory to store:
Congurable settings like VO(max), and VO.
Warning and fault thresholds for overvoltage, overcurrent, and overtemperature.
Calibration information like coefcients.
During start-up the RESTORE_USER_ALL command is called to store all USER
parameters into the running conguration. When settings are changed
STORE_USER_ALL can be used to store the changed settings into the USER NVRAM
storage area. RESTORE_DEFAULT_ALL and STORE_DEFAULT_ALL can be used to
change parameters in the DEFAULT storage area. The running conguration needs to be
used to swap between USER and DEFAULT storage area.
10.3 PMBus commands
Table 11 contains a list of the PMBus commands.
Hex = PMBus command hex value, Command Name = PMBus command name,
# = Number of Data Bytes. R/W/C = Read / Write / Command. Some commands are R/W
where they are only dened as Read in the PMBus. The Write is supported to enable
factory programming.
Table 11.
PMBus commands
Hex Command name
#
SMBus
transaction
type
Default
value
Supported
range
Comments
ON, OFF, and margin testing
00
PAGE
1
R/W
01
OPERATION[1]
1
R/W
0x80
02
ON_OFF CONFIG[1]
1
R/W
0x18
03
CLEAR_FAULTS[1]
0C
04
PHASE
05
Reserved
06
Reserved
相關PDF資料 |
PDF描述 |
|---|---|
| PJ3843BCS | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| PJ3842BCD | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8 |
| PJ3842BCS | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO8 |
| PJ3843BCD | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8 |
| PJ3845BCD | 1 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIP84 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:TRANSIENT ABSORPTION ZENER |
| PIPA043051 | 制造商:OPLINK 制造商全稱:OPLINK Communications Inc. 功能描述:Pigtail Integrated InGaAs PIN Photodiode Array |
| PIPA043052 | 制造商:OPLINK 制造商全稱:OPLINK Communications Inc. 功能描述:Pigtail Integrated InGaAs PIN Photodiode Array |
| PIPA043201 | 制造商:OPLINK 制造商全稱:OPLINK Communications Inc. 功能描述:Pigtail Integrated InGaAs PIN Photodiode Array |
| PIPA043202 | 制造商:OPLINK 制造商全稱:OPLINK Communications Inc. 功能描述:Pigtail Integrated InGaAs PIN Photodiode Array |
發布緊急采購，3分鐘左右您將得到回復。