參數資料
型號: PIC16LF1828-E/P
廠商: Microchip Technology
文件頁數: 17/101頁
文件大?。?/td> 0K
描述: IC MCU 8BIT 7KB FLASH 20PDIP
標準包裝: 22
系列: PIC® XLP™ mTouch™ 16F
核心處理器: PIC
芯體尺寸: 8-位
速度: 32MHz
連通性: I²C,SPI,UART/USART
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 17
程序存儲器容量: 7KB(4K x 14)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 256 x 8
RAM 容量: 256 x 8
電壓 - 電源 (Vcc/Vdd): 1.8 V ~ 3.6 V
數據轉換器: A/D 12x10b
振蕩器型: 內部
工作溫度: -40°C ~ 125°C
封裝/外殼: 20-DIP(0.300",7.62mm)
包裝: 管件
163
2552K–AVR–04/11
ATmega329/3290/649/6490
18.3
SS Pin Functionality
18.3.1
Slave Mode
When the SPI is configured as a Slave, the Slave Select (SS) pin is always input. When SS is
held low, the SPI is activated, and MISO becomes an output if configured so by the user. All
other pins are inputs. When SS is driven high, all pins are inputs, and the SPI is passive, which
means that it will not receive incoming data. Note that the SPI logic will be reset once the SS pin
is driven high.
The SS pin is useful for packet/byte synchronization to keep the slave bit counter synchronous
with the master clock generator. When the SS pin is driven high, the SPI slave will immediately
reset the send and receive logic, and drop any partially received data in the Shift Register.
18.3.2
Master Mode
When the SPI is configured as a Master (MSTR in SPCR is set), the user can determine the
direction of the SS pin.
If SS is configured as an output, the pin is a general output pin which does not affect the SPI
system. Typically, the pin will be driving the SS pin of the SPI Slave.
If SS is configured as an input, it must be held high to ensure Master SPI operation. If the SS pin
is driven low by peripheral circuitry when the SPI is configured as a Master with the SS pin
defined as an input, the SPI system interprets this as another master selecting the SPI as a
slave and starting to send data to it. To avoid bus contention, the SPI system takes the following
actions:
1.
The MSTR bit in SPCR is cleared and the SPI system becomes a Slave. As a result of
the SPI becoming a Slave, the MOSI and SCK pins become inputs.
2.
The SPIF Flag in SPSR is set, and if the SPI interrupt is enabled, and the I-bit in SREG is
set, the interrupt routine will be executed.
Thus, when interrupt-driven SPI transmission is used in Master mode, and there exists a possi-
bility that SS is driven low, the interrupt should always check that the MSTR bit is still set. If the
MSTR bit has been cleared by a slave select, it must be set by the user to re-enable SPI Master
mode.
相關PDF資料
PDF描述
PIC16LF1829-I/P MCU PIC 14KB FLASH 20-DIP
PIC16LF1847-I/ML MCU 14KB FLASH 1KB RAM 28-QFN
PIC16LF1903-E/SP MCU 7KB FLASH 256B RAM 28SPDIP
PIC16LF1907-E/P MCU 14KB FLASH 512B RAM 40PDIP
PIC16LF1933-E/SP MCU PIC 8BIT 4K FLASH 28SDIP
相關代理商/技術參數
參數描述
PIC16LF1828-I/ML 功能描述:8位微控制器 -MCU 7 KB Flash 256B RAM 32 MHz Int Osc RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LF1828-I/P 功能描述:8位微控制器 -MCU 7 KB Flash 256B RAM 32 MHz Int Osc RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LF1828-I/SO 功能描述:8位微控制器 -MCU 7 KB Flash 256B RAM 32 MHz Int Osc RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LF1828-I/SS 功能描述:8位微控制器 -MCU 7 KB Flash 256b RAM 32 MHz Int Osc RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16LF1828T-I/ML 功能描述:8位微控制器 -MCU 7 KB Flash 256B RAM 32 MHz Int Osc RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT