參數資料
型號: PIC12F683T-I/MD
廠商: Microchip Technology
文件頁數: 137/176頁
文件大?。?/td> 0K
描述: IC PIC MCU FLASH 2KX14 8DFN
產品培訓模塊: Asynchronous Stimulus
Digi-Key 應用說明: AN0005 PWM Example with Microchip's CCP Module
AN0005 Example Code
標準包裝: 3,300
系列: PIC® 12F
核心處理器: PIC
芯體尺寸: 8-位
速度: 20MHz
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 5
程序存儲器容量: 3.5KB(2K x 14)
程序存儲器類型: 閃存
EEPROM 大小: 256 x 8
RAM 容量: 128 x 8
電壓 - 電源 (Vcc/Vdd): 2 V ~ 5.5 V
數據轉換器: A/D 4x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 8-VDFN 裸露焊盤
包裝: 帶卷 (TR)
配用: AC164326-ND - MODULA SKT PM3 20QFN
I3-DB12F683-ND - BOARD DAUGHTER ICEPIC3
2007 Microchip Technology Inc.
DS41211D-page 61
PIC12F683
9.0
ANALOG-TO-DIGITAL
CONVERTER (ADC) MODULE
The
Analog-to-Digital
Converter
(ADC)
allows
conversion of an analog input signal to a 10-bit binary
representation of that signal. This device uses analog
inputs, which are multiplexed into a single sample and
hold circuit. The output of the sample and hold is
connected to the input of the converter. The converter
generates a 10-bit binary result via successive
approximation and stores the conversion result into the
ADC result registers (ADRESL and ADRESH).
The ADC voltage reference is software selectable to
either VDD or a voltage applied to the external reference
pins.
The ADC can generate an interrupt upon completion of
a conversion. This interrupt can be used to wake-up the
device from Sleep.
Figure 9-1 shows the block diagram of the ADC.
FIGURE 9-1:
ADC BLOCK DIAGRAM
9.1
ADC Configuration
When configuring and using the ADC the following
functions must be considered:
GPIO configuration
Channel selection
ADC voltage reference selection
ADC conversion clock source
Interrupt control
Results formatting
9.1.1
GPIO CONFIGURATION
The ADC can be used to convert both analog and digital
signals. When converting analog signals, the I/O pin
should be configured for analog by setting the associated
TRIS and ANSEL bits. See the corresponding GPIO
section for more information.
9.1.2
CHANNEL SELECTION
The CHS bits of the ADCON0 register determine which
channel is connected to the sample and hold circuit.
When changing channels, a delay is required before
starting the next conversion. Refer to Section 9.2
“ADC Operation” for more information.
GP0/AN0
A/D
GP1/AN1/VREF
GP2/AN2
VDD
VREF
ADON
GO/DONE
VCFG = 1
VCFG = 0
CHS
ADRESH
ADRESL
10
ADFM
GP4/AN3
0
= Left Justify
1
= Right Justify
Note:
Analog voltages on any pin that is defined
as a digital input may cause the input
buffer to conduct excess current.
相關PDF資料
PDF描述
PIC18F45J10T-I/ML IC PIC MCU FLASH 16KX16 44QFN
PIC16LF628AT-I/SO IC MCU FLASH 2KX14 EEPROM 18SOIC
V300A2C160B CONVERTER MOD DC/DC 2V 160W
V300A28C400BL2 CONVERTER MOD DC/DC 28V 400W
V300A28C400BF3 CONVERTER MOD DC/DC 28V 400W
相關代理商/技術參數
參數描述
PIC12F752 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin Flash-Based 8-Bit CMOS Microcontrollers
PIC12F752-E/MF 功能描述:8位微控制器 -MCU 1.75KB 64BRAM 6 I/O 8MHz Int Osc 5MIPS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC12F752-E/P 功能描述:8位微控制器 -MCU 1.75KB 64BRAM 6 I/O 8MHz Int Osc 5MIPS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC12F752-E/SN 功能描述:8位微控制器 -MCU 1.75KB 64BRAM 6 I/O 8MHz Int Osc 5MIPS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC12F752-I/MF 功能描述:8位微控制器 -MCU 1.75KB 64BRAM 6 I/O 8MHz Int Osc 5MIPS RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT