- 您現在的位置：買賣IC網 > PDF目錄369960 > PDI1394P22BD (NXP SEMICONDUCTORS) 3-port physical layer interface PDF資料下載
參數資料
| 型號： | PDI1394P22BD |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 3-port physical layer interface |
| 中文描述： | 3 CHANNEL(S), 400M bps, SERIAL COMM CONTROLLER, PQFP64 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64 |
| 文件頁數： | 7/42頁 |
| 文件大?。?/td> | 233K |
| 代理商： | PDI1394P22BD |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Philips Semiconductors
Preliminary data
PDI1394P23
2-port/1-port 400 Mbps physical layer interface
2001 Sep 06
7
Name
Description
I/O
LFBGA
Ball
Numbers
LQFP
Pin
Numbers
Pin Type
PLLGND
Supply
57, 58
E1, D3
—
PLL circuit ground terminals. These terminals should be tied together to
the low impedance circuit board ground plane.
PLLV
DD
Supply
56
D1, D4
—
PLL circuit power terminals. A combination of high frequency decoupling
capacitors near each terminal are suggested, such as paralleled 0.1
μ
F
and 0.001
μ
F. This supply terminals is separated from DV
DD
and AV
DD
internal to the device to provide noise isolation. They should be tied at a
low impedance point on the circuit board.
R0
R1
Bias
40
41
D5
A4
—
Current setting resistor pins. These pins are connected to an external
resistor to set the internal operating currents and cable driver output
currents. A resistance of 6.34 k
±
1% is required to meet the IEEE
1394–1995 Std. output voltage limits.
RESET
CMOS 5V tol
53
C1
I
Logic reset input. Asserting this terminal low resets the internal logic. An
internal pull-up resistor to V
is provided so only an external
delay capacitor is required for proper power-up operation. For more
information, refer to Section 17.2. This input is otherwise a standard
Schmitt logic input, and can also be driven by an open-drain type driver.
SYSCLK
CMOS
2
H2
O
System clock output. Provides a 49.152 MHz clock signal, synchronized
with data transfers, to the LLC.
TEST0
CMOS
29
C8
I
Test control input. This input is used in manufacturing tests of the
PDI1394P23. For normal use, this terminal should be tied to GND.
TPA0+,
TPA1+
Cable
37
46
B5
B3
I/O
Twisted-pair cable A differential signal terminals. Board traces from each
pair of positive and negative differential signal terminals should be kept
matched and as short as possible to the external load resistors and to
the cable connector. TPA1+ and TPA1– can be left unconnected if the
TWOPORT pin is tied to DGND.
TPA0–,
TPA1–
Cable
36
45
B6
A3
I/O
TPB0+,
TPB1+
Cable
35
44
C6
C4
I/O
Twisted-pair cable B differential signal terminals. Board traces from each
pair of positive and negative differential signal terminals should be kept
matched and as short as possible to the external load resistors and to
the cable connector. TPB1+ and TPB1– can be left unconnected if the
TWOPORT pin is tied to DGND.
TPB0–,
TPB1–
Cable
34
43
A7
B4
I/O
TPBIAS0,
TPBIAS1
Cable
38
47
A6
A2
I/O
Twisted-pair bias output. This provides the 1.86V nominal bias voltage
needed for proper operation of the twisted-pair cable drivers and
receivers, and for signaling to the remote nodes that there is an active
cable connection. These terminals must be decoupled with a
0.3
μ
F–1
μ
F capacitor to ground. TPBIAS1 can be left unconnected if
the TWOPORT pin is tied to DGND.
TWOPORT
27
D7
One/two port selector pin. This pin should be tied to DV
for two port
operation and tied to DGND for one port operation. When tied to DV
DD
,
both ports 0 and 1 are operational. When tied to DGND, port 0 is
operational and port 1 is disabled.
XI
XO
Crystal
59
60
E2
E3
—
Crystal oscillator inputs. These terminals connect to a 24.576 MHz
parallel resonant fundamental mode crystal. The optimum values for the
external shunt capacitors are dependent on the specifications of the
crystal used. Can also be driven by an external clock generator (leave
XO unconnected in this case and start supplying the external clock
before resetting the PDI1394P23). For more information, refer to
Section 17.5
相關PDF資料 |
PDF描述 |
|---|---|
| PDI1394L11BA | 1394 AV link layer controller |
| PDI1394L21BE | 1394 full duplex AV link layer controller |
| PDI1394L21BP | 1394 full duplex AV link layer controller |
| PDL-TTL-7-1 | Programmable Delay Line |
| PDL-TTL-7-14 | Programmable Delay Line |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PDI1394P23 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-port/1-port 400 Mbps physical layer interface |
| PDI1394P23BD | 功能描述:IC IEEE 1394 LINK CTRLR 64LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| PDI1394P23BD,118 | 功能描述:輸入/輸出控制器接口集成電路 1394 2-PORT PHY NO NEW DESIGNS RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| PDI1394P23BD,151 | 功能描述:輸入/輸出控制器接口集成電路 DO NOT USE ORDER -T PART RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| PDI1394P23BD,157 | 功能描述:輸入/輸出控制器接口集成電路 IEEE1394A 2 PORT PHY RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。