- 您現在的位置：買賣IC網 > PDF目錄378045 > PCI4515 (Texas Instruments, Inc.) SINGLE SOCKET CARDBUS CONTROLLER WITH INTEGRATED PDF資料下載
參數資料
| 型號： | PCI4515 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | SINGLE SOCKET CARDBUS CONTROLLER WITH INTEGRATED |
| 中文描述： | 單插槽CardBus控制器，它集成 |
| 文件頁數： | 41/216頁 |
| 文件大?。?/td> | 1138K |
| 代理商： | PCI4515 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁
33
PCI LOCK indicates an atomic operation that may require multiple transactions to complete. When LOCK is asserted,
nonexclusive transactions can proceed to an address that is not currently locked. A grant to start a transaction on
the PCI bus does not assure control of LOCK; control of LOCK is obtained under its own protocol. It is possible for
different initiators to use the PCI bus while a single master retains ownership of LOCK. Note that the CardBus signal
for this protocol is CBLOCK to avoid confusion with the bus clock.
An agent may need to do an exclusive operation because a critical access to memory might be broken into several
transactions, but the master wants exclusive rights to a region of memory. The granularity of the lock is defined by
PCI to be 16 bytes, aligned. The LOCK protocol defined by the
PCI Local Bus Specification
allows a resource lock
without interfering with nonexclusive real-time data transfer, such as video.
The PCI bus arbiter may be designed to support only complete bus locks using the LOCK protocol. In this scenario,
the arbiter does not grant the bus to any other agent (other than the LOCK master) while LOCK is asserted. A
complete bus lock may have a significant impact on the performance of the video. The arbiter that supports complete
bus LOCK must grant the bus to the cache to perform a writeback due to a snoop to a modified line when a locked
operation is in progress.
The PCI4515 controller supports all LOCK protocols associated with PCI-to-PCI bridges, as also defined for
PCI-to-CardBus bridges. This includes disabling write posting while a locked operation is in progress, which can solve
a potential deadlock when using devices such as PCI-to-PCI bridges. The potential deadlock can occur if a CardBus
target supports delayed transactions and blocks access to the target until it completes a delayed read. This target
characteristic is prohibited by the
PCI Local Bus Specification
, and the issue is resolved by the PCI master using
LOCK.
3.4.4
Serial EEPROM I
2
C Bus
The PCI4515 controller offers many choices for modes of operation, and these choices are selected by programming
several configuration registers. For system board applications, these registers are normally programmed through the
BIOS routine. For add-in card and docking-station/port-replicator applications, the PCI4515 controller provides a
two-wire inter-integrated circuit (IIC or I
2
C) serial bus for use with an external serial EEPROM.
The PCI4515 controller is always the bus master, and the EEPROM is always the slave. Either device can drive the
bus low, but neither device drives the bus high. The high level is achieved through the use of pullup resistors on the
SCL and SDA signal lines. The PCI4515 controller is always the source of the clock signal, SCL.
System designers who wish to load register values with a serial EEPROM must use pullup resistors on the SCL and
SDA terminals. If the PCI4515 controller detects a logic-high level on the SCL terminal at the end of GRST, then it
initiates incremental reads from the external EEPROM. Any size serial EEPROM up to the I
2
C limit of 16 Kbits can
be used, but only the first 96 bytes (from offset 00h to offset 5Fh) are required to configure the PCI4515 controller.
Figure 33 shows a serial EEPROM application.
In addition to loading configuration data from an EEPROM, the PCI4515 I
2
C bus can be used to read and write from
other I
2
C serial devices. A system designer can control the I
2
C bus, using the PCI4515 controller as bus master, by
reading and writing PCI configuration registers
. Setting bit 3 (SBDETECT) in the serial bus control/status register (PCI
offset B3h, see Section 4.49) causes the PCI4515 controller to route the SDA and SCL signals to the SDA and SCL
terminals, respectively. The read/write data, slave address, and byte addresses are manipulated by accessing the
serial bus data, serial bus index, and serial bus slave address registers (PCI offsets B0h, B1h, and B2h; see Sections
4.46, 4.47, and 4.48, respectively).
EEPROM interface status information is communicated through the serial bus control and status register (PCI offset
B3h, see Section 4.49). Bit 3 (SBDETECT) in this register indicates whether or not the PCI4515 serial ROM circuitry
detects the pullup resistor on SCL. Any undefined condition, such as a missing acknowledge, results in bit 0
(ROM_ERR) being set. Bit 4 (ROMBUSY) is set while the subsystem ID register is loading (serial ROM interface is
busy).
The subsystem vendor ID for function 2 is also loaded through EEPROM. The EEPROM load data goes to all three
functions from the serial EEPROM loader.
相關PDF資料 |
PDF描述 |
|---|---|
| PCI4515GHK | SINGLE SOCKET CARDBUS CONTROLLER WITH INTEGRATED |
| PCI4515ZHK | SINGLE SOCKET CARDBUS CONTROLLER WITH INTEGRATED |
| PCI6420 | Integrated 2-Slot PC Card & Dedicated Flash Media Controller |
| PCI6421 | DUAL/SINGLE SOCKET CARDBUS AND ULTRAMEDIA CONTROLLER |
| PCI6611 | DUAL/SINGLE SOCKET CARDBUS AND ULTRAMEDIA CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCI4515A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Single Socket CardBus Controller with Integrated 1394a-2000 OHCI One-Port PHY/Link-Layer Controller |
| PCI4515AGHK | 功能描述:外圍驅動器與原件 - PCI Single Socket CardBus Controller RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PCI4515AZHK | 功能描述:外圍驅動器與原件 - PCI Single Socket CardBus Controller RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| PCI4515GHK | 功能描述:IC PC CARD CNTRLR 257-BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| PCI4515ZHK | 功能描述:IC PC CARD CONTROLLER 257-BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
發布緊急采購，3分鐘左右您將得到回復。