參數資料
型號： PCF2113AU10
廠商： NXP Semiconductors N.V.
英文描述： RECTIFIER SBR DUAL 20A 60V 180A-ifsm 650mV-vf 0.5mA-ir TO-220AB 50/TUBE
中文描述： LCD控制器/驅動器
文件頁數： 32/72頁
文件大?。?/td> 332K
代理商： PCF2113AU10
2001 Dec 19
32
Philips Semiconductors
Product specification
LCD controllers/drivers
PCF2113x
10 INTERFACES TO MICROCONTROLLER
10.1
Parallel interface
ThePCF2113xcansenddataineithertwo4-bitoperations
or one 8-bit operation and can thus interface to 4-bit or
8-bit microcontrollers.
In 8-bit mode data is transferred as 8-bit bytes using the
8 data lines DB7 to DB0. Three further control lines E,
RS and R/W are required (see Chapter 6).
In 4-bit mode data is transferred in two cycles of 4 bits
each using pins DB7 to DB4 for the transaction.
The higher order bits (corresponding to DB7 to DB4 in
8-bit mode) are sent in the first cycle and the lower order
bits (DB3 to DB0 in 8-bit mode) in the second cycle. Data
transfer is complete after two 4-bit data transfers. It should
be noted that two cycles are also required for the busy flag
check. 4-bit operation is selected by instruction, see
Figs 17 to 19 for examples of bus protocol.
In 4-bit mode, pins DB3 to DB0 must be left open-circuit.
They are pulled up to V
DD
internally.
10.2
I
2
C-bus interface
The I
2
C-bus is for bidirectional, two-line communication
between different ICs or modules. The two lines are the
Serial Data line (SDA) and the Serial Clock Line (SCL).
Both lines must be connected to a positive supply via
pull-up resistors. Data transfer may be initiated only when
the bus is not busy.
Each byte of eight bits is followed by an acknowledge bit.
The acknowledge bit is a HIGH level signal put on the bus
by the transmitter during which time the master generates
anextraacknowledgerelatedclockpulse.Aslavereceiver
which is addressed must generate an acknowledge after
the reception of each byte.
Also a master receiver must generate an acknowledge
after the reception of each byte that has been clocked out
of the slave transmitter.
The device that acknowledges must pull-down the SDA
line during the acknowledge clock pulse, so that the SDA
line is stable LOW during the HIGH period of the
acknowledge related clock pulse (set-up and hold times
must be taken into consideration).
MGA804
RS
E
DB7
R/W
DB6
DB5
DB4
instruction
write
busy flag and
address counter read
data register
read
IR7
IR3
BF
AC3
DR7
DR3
IR6
IR2
AC6
AC2
DR6
DR2
IR5
IR1
AC5
AC1
DR5
DR1
IR4
IR0
AC4
AC0
DR4
DR0
Fig.17 4-bit transfer example.
相關PDF資料
PDF描述
PCF2113EU2 LCD controllers/drivers
PCF2113EUF4 LCD controllers/drivers
PCF2113A LCD controller/driver
PCF2113D LCD controller/driver
PCF2113DU10 LCD controllers/drivers
相關代理商/技術參數
參數描述
PCF2113AUF4 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers
PCF2113D 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controller/driver
PCF2113DH 制造商:NXP Semiconductors 功能描述:18 X 60 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP100
PCF2113DH/4 功能描述:LCD 驅動器 I2C LCD CHARCTR DRVR RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
PCF2113DH/4,557 功能描述:LCD 驅動器 I2C LCD CHARCTR DRVR RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*