參數資料
型號： PCA9670PW,118
廠商： NXP Semiconductors
文件頁數： 3/35頁
文件大小： 0K
描述： IC I/O EXPANDER I2C 8B 16TSSOP
標準包裝： 2,500
接口： I²C
輸入/輸出數： 8
中斷輸出： 無
頻率 - 時鐘： 1MHz
電源電壓： 2.3 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 16-TSSOP
包裝： 帶卷 (TR)
包括： POR
其它名稱： 935282716118
PCA9670PW-T
PCA9670PW-T-ND
PCA9670
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 3 — 30 May 2013
11 of 35
NXP Semiconductors
PCA9670
Remote 8-bit I/O expander for Fm+ I2C-bus with reset
8.
I/O programming
8.1 Quasi-bidirectional I/O architecture
A quasi-bidirectional I/O is an input or output port without using a direction control register.
Whenever the master reads the register, the value returned to master depends on the
actual voltage or status of the pin. At power-on, all the ports are HIGH with a weak 100
A
internal pull-up to VDD but can be driven LOW by an internal transistor, or an external
signal. The I/O ports are entirely independent of each other but each I/O octal is controlled
by the same read or write data byte.
Advantages of the quasi-bidirectional I/O over totem pole I/O include:
Better for driving LEDs since the p-channel (transistor to VDD) is small, which saves
die size and therefore cost. LED drive only requires an internal transistor to ground,
while the LED is connected to VDD through a current-limiting resistor. Totem pole I/O
have both an n-channel and p-channel transistors, which allow solid HIGH and LOW
output levels without a pull-up resistor — good for logic levels.
Simpler architecture — only a single register and the I/O can be both input and output
at the same time. Totem pole I/O have a direction register which specifies the port pin
direction and it is always in that configuration unless the direction is explicitly
changed.
Does not require a command byte. The simplicity of one register (no need for the
pointer register or technically, the command byte) is an advantage in some embedded
systems where every byte counts because of memory or bandwidth limitations.
There is only one register to control four possibilities of the port pin: Input HIGH, input
LOW, output HIGH or output LOW.
Input HIGH: The master needs to write 1 to the register to set the port as an input mode
if the device is not in the default power-on condition. The master reads the register to
check the input status. If the external source pulls the port pin up to VDD or drives
logic 1, then the master will read the value of 1.
Input LOW: The master needs to write 1 to the register to set the port to input mode if
the device is not in the default power-on condition. The master reads the register to
check the input status. If the external source pulls the port pin down to VSS or drives
logic 0, which sinks the weak 100
A current source, then the master will read the value
of 0.
Output HIGH: The master writes 1 to the register. There is an additional ‘a(chǎn)ccelerator’ or
strong pull-up current when the master sets the port HIGH. The additional strong pull-up
is only active during the HIGH time of the acknowledge clock cycle. This accelerator
current helps the port’s 100
A current source make a faster rising edge into a heavily
loaded output, but only at the start of the acknowledge clock cycle to avoid bus
contention if an external signal is pulling the port LOW to VSS/driving the port with
logic 0 at the same time. After the half clock cycle there is only the 100
A current
source to hold the port HIGH.
Output LOW: The master writes 0 to the register. There is a strong current sink
transistor that holds the port pin LOW. A large current may flow into the port, which
could potentially damage the part if the master writes a 0 to the register and an external
source is pulling the port HIGH at the same time.
相關PDF資料
PDF描述
PCA9674TS,118 IC I/O EXPANDER I2C 8B 20SSOP
PCA9674ATS,118 IC I/O EXPANDER I2C 8B 20SSOP
PCA9674PW,112 IC I/O EXPANDER I2C 8B 16TSSOP
PCA9554D,118 IC I/O EXPANDER I2C 8B 16SOIC
PCA9554ATS,112 IC I/O EXPANDER I2C 8B 20SSOP
相關代理商/技術參數
參數描述
PCA9670PW-T 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB GPIO INT PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671BQ,118 功能描述:接口-I/O擴展器 REMOTE 16BIT GPIO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671BQ-T 功能描述:接口-I/O擴展器 REMOTE 16BIT GPIO FM+I2C-RESET RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671BS,118 功能描述:接口-I/O擴展器 REMOTE 16BIT GPIO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
PCA9671BS-T 功能描述:接口-I/O擴展器 REMOTE 16BIT GPIO FM+I2C-RESET RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*