- 您現在的位置：買賣IC網 > PDF目錄367809 > PCA9542PW (NXP SEMICONDUCTORS) 2-channel I2C multiplexer and interrupt controller PDF資料下載
參數資料
| 型號： | PCA9542PW |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 通用總線功能 |
| 英文描述： | 2-channel I2C multiplexer and interrupt controller |
| 中文描述： | 9542 SERIES, 2 LINE TO 1 LINE MULTIPLEXER, TRUE OUTPUT, PDSO14 |
| 封裝： | 4.40 MM, PLASTIC, MO-153, SOT402-1, TSSOP-14 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 74K |
| 代理商： | PCA9542PW |
Philips Semiconductors
Product specification
PCA9542
2-channel I
2
C multiplexer and interrupt controller
1999 Oct 07
4
CHANNEL SELECTION
A SC0x/SD0x downstream pair, or channel, is selected by the
contents of the control register. This register is written after the
PCA9542 has been addressed. The 3 LSBs of the control byte are
used to determine which channel is to be selected. When a channel
is selected, the channel will become active after a stop condition has
been placed on the I
2
C bus. This ensures that all SCx/SDx lines will
be in a HIGH state when the channel is made active, so that no
false conditions are generated at the time of connection.
CONTROL BYTE
SELECTED
CHANNEL
7
X
X
X
6
X
X
X
5
X
X
X
4
X
X
X
3
X
X
X
2
0
1
1
1
X
0
0
0
X
0
1
none
0 (SC0/SD0)
1 (SC1/SD1)
CONTROL REGISTER
X INT1 INT0
B2
B1 B0
Channel select bits
(read/write)
Interrupt bits
(read only)
X
SW00477
X
6
5
4
2
1
0
7
3
POWER-ON RESET
During power-up, the control register defaults to all zeroes causing
all the channels to be deselected.
INTERRUPT HANDLING
The PCA9542 provides 2 interrupt inputs, one for each channel and
one open drain interrupt output. When an interrupt is generated by any
device, it will be detected by the PCA9542 and the interrupt output
will be driven LOW. The channel need not be active for detection of
the interrupt. A bit is also set in the control byte.
Bits 4 – 5 of the control byte correspond to channels 0 – 1 of the
PCA9542, respectively. Therefore, if an interrupt is generated by any
device connected to channel 1, then bit 5 will be set in the control
register. Likewise, an interrupt on any device connected to channel 0
would cause bit 4 of the control register to be set. The master can
then address the PCA9542 and read the contents of the control byte
to determine which channel contains the device generating the
interrupt. The master can then reconfigure the PCA9542 to select this
channel, and locate the device generating the interrupt and clear it.
It should be noted that more than one device can be providing an
interrupt on a channel, so it is up to the master to ensure that all
devices on a channel are interrogated for an interrupt.
7
6
5
4
3
2
1
0
INTERRUPTING
CHANNEL
0 (SC0/SD0)
1 (SC1/SD1)
0
0
0
0
0
1
1
0
X
X
X
X
X
X
X
X
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9542PWDH | 2-channel I2C multiplexer and interrupt controller |
| PCA9543 | 2-channel I2C switch with interrupt logic and reset |
| PCA9543D | 2-channel I2C switch with interrupt logic and reset |
| PCA9543PW | 2-channel I2C switch with interrupt logic and reset |
| PCA9544D | BUS CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9542PWDH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-channel I2C multiplexer and interrupt controller |
| PCA9543 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-channel I2C switch with interrupt logic and reset |
| PCA9543A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-channel I2C-bus switch with interrupt logic and reset |
| PCA9543A_09 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-channel I2C-bus switch with interrupt logic and reset |
| PCA9543AD | 功能描述:多路器開關 IC 2Ch I2C-Bus Switch RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。