參數資料
型號： PCA9513A
廠商： NXP Semiconductors N.V.
英文描述： Hot swappable I2C-bus and SMBus bus buffer
中文描述： 熱插拔I2C總線和SMBus總線緩沖器
文件頁數： 5/25頁
文件大?。?/td> 142K
代理商： PCA9513A
PCA9513A_PCA9514A_1
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 11 October 2005
5 of 25
Philips Semiconductors
PCA9513A; PCA9514A
Hot swappable I
2
C-bus and SMBus bus buffer
7.
Pinning information
7.1 Pinning
7.2 Pin description
8.
Functional description
Refer to
Figure 1 “Block diagram of PCA9513A”
and
Figure 2 “Block diagram of
PCA9514A”
.
8.1 Start-up
An undervoltage and initialization circuit holds the parts in a disconnected state which
presents high-impedance to all SDAn and SCLn pins during power-up. A LOW on the
ENABLE pin also forces the parts into the low current disconnected state when the I
CC
is
essentially zero. As the power supply is brought up and the ENABLE is HIGH or the part is
powered and the ENABLE is taken from LOW to HIGH it enters an initialization state
where the internal references are stabilized and the 92
μ
A input pull-ups (on the
PCA9513A) is enabled. At the end of the initialization state the ‘Stop Bit And Bus Idle’
detect circuit is enabled. With the ENABLE pin HIGH long enough to complete the
initialization state (t
en
) and remaining HIGH when all the SDAn and SCLn pins have been
Fig 3.
Pin configuration for SO8
Fig 4.
Pin configuration for TSSOP8
(MSOP8)
PCA9513AD
PCA9514AD
ENABLE
V
CC
SCLOUT
SDAOUT
SCLIN
SDAIN
GND
READY
002aab676
1
2
3
4
6
5
8
7
PCA9513ADP
PCA9514ADP
ENABLE
V
CC
SDAOUT
SCLOUT
SCLIN
SDAIN
GND
READY
002aab677
1
2
3
4
6
5
8
7
Table 3:
Symbol
ENABLE
Pin description
Pin
1
Description
Chip enable. Grounding this input puts the part in a Low current (< 1
μ
A)
mode. It also disables the rise time accelerators, isolates SDAIN from
SDAOUT and isolates SCLIN from SCLOUT.
serial clock output to and from the SCL bus on the card
serial clock input to and from the SCL bus on the backplane
Ground. Connect this pin to a ground plane for best results.
open-drain output which pulls LOW when SDAIN and SCLIN are
disconnected from SDAOUT and SCLOUT, and goes HIGH when the two
sides are connected
serial data input to and from the SDA bus on the backplane
serial data output to and from the SDA bus on the card
power supply
SCLOUT
SCLIN
GND
READY
2
3
4
5
SDAIN
SDAOUT
V
CC
6
7
8
相關PDF資料
PDF描述
PCA9514A Hot swappable I2C-bus and SMBus bus buffer
PCA9516A 5-channel I2C hub
PCA9519 4-channel level translating I2C-bus/SMBus repeater
PCA9540B 2-channel I2C multiplexer
PCA9540PWDH 2-channel I2C multiplexer
相關代理商/技術參數
參數描述
PCA9513AD 功能描述:緩沖器和線路驅動器 HOT SWAP I2C/SMBUS BUS BUFFER RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
PCA9513AD,112 功能描述:緩沖器和線路驅動器 HOT SWAP I2C/SMBUS RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
PCA9513AD,118 功能描述:緩沖器和線路驅動器 HOT SWAP I2C/SMBUS RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
PCA9513AD112 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述:
PCA9513ADP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Hot swappable I2C-bus and SMBus bus buffer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*