參數資料
型號： PC7410VGSU400N
廠商： Atmel Corp.
英文描述： PowerPC 7410 RISC Microprocessor Product Specification
中文描述： 7410的PowerPC RISC微處理器產品規格
文件頁數： 24/54頁
文件大?。?/td> 692K
代理商： PC7410VGSU400N
24
PC7410
2141D–HIREL–02/04
L2 input and output signals are latched or enabled respectively by the internal L2CLK
(which is SYSCLK multiplied up to the core frequency and divided down to the L2CLK
frequency). In other words, the AC timings of Table 13 are entirely independent of
L2SYNC_IN. In a closed loop system, where L2SYNC_IN is driven through the board
trace by L2SYNC_OUT, L2SYNC_IN only controls the output phase of L2CLKOUTA
and L2CLKOUTB which are used to latch or enable data at the SRAMs. However, since
in a closed loop system L2SYNC_IN is held in phase alignment with the internal L2CLK,
the signals of Table 13 are referenced to this signal rather than the not-externally-visible
internal L2CLK. During manufacturing test, these times are actually measured relative to
SYSCLK.
Notes:
1. L2CLK outputs are L2CLK_OUTA, L2CLK_OUTB, and L2SYNC_OUT pins. The L2CLK frequency to core frequency set-
tings must be chosen such that the resulting L2CLK frequency and core frequency do not exceed their respective maximum
or minimum operating frequencies. The maximum L2LCK frequency will be system-dependent. L2CLK_OUTA and
L2CLK_OUTB must have equal loading.
2. The nominal duty cycle of the L2CLK is 50% measured at midpoint voltage.
3. The DLL re-lock time is specified in terms of L2CLKs. The number in the table must be multiplied by the period of L2CLK to
compute the actual time duration in nanoseconds. Re-lock timing is guaranteed by design and characterization.
4. The L2CR[L2SL] bit should be set for L2CLK frequencies less than 110 MHz. This adds more delay to each tap of the DLL.
5. Allowable skew between L2SYNC_OUT and L2SYNC_IN.
6. Guaranteed by design and not tested. This output jitter number represents the maximum delay of one tap forward or one tap
back from the current DLL tap as the phase comparator seeks to minimize the phase difference between L2SYNC_IN and
the internal L2CLK. This number must be comprehended in the L2 timing analysis. The input jitter on SYSCLK affects
L2CLKOUT and the L2 address/data/control signals equally and therefore is already comprehended in the AC timing and
does not have to be considered in the L2 timing analysis.
Table 12.
L2CLK Output AC Timing Specifications at Recommended Operating Conditions (See Table 4)
Symbol
Parameter
400 MHz
450 MHz
500 MHz
Unit
Min
Max
Min
Max
Min
Max
f
L2CLK
(1)(4)
L2CLK frequency
133
400
133
400
133
400
MHz
t
L2CLK
L2CLK cycle time
2.5
7.5
2.5
7.5
2.5
7.5
ns
t
CHCL
/t
L2CLK
(2)
L2CLK duty cycle
50
50
50
%
Internal DLL-relock time
(3)
640
640
640
-
L2CLK
DLL capture window
(5)
0
10
0
10
0
10
ns
t
L2CSKW
L2CLKOUT output-to-output
skew
(6)
-
50
-
50
-
50
ps
L2CLKOUT output jitter
(6)
-
±150
-
±150
-
±150
ps
相關PDF資料
PDF描述
PC7410VGSU450L PowerPC 7410 RISC Microprocessor Product Specification
PC7410VGSU450N PowerPC 7410 RISC Microprocessor Product Specification
PC7410VGSU500L PowerPC 7410 RISC Microprocessor Product Specification
PC7410VGSU500N PowerPC 7410 RISC Microprocessor Product Specification
PC7410VGU400L PowerPC 7410 RISC Microprocessor Product Specification
相關代理商/技術參數
參數描述
PC7410VGSU450L 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:PowerPC 7410 RISC Microprocessor Product Specification
PC7410VGSU450N 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:PowerPC 7410 RISC Microprocessor Product Specification
PC7410VGSU500L 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:PowerPC 7410 RISC Microprocessor Product Specification
PC7410VGSU500N 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:PowerPC 7410 RISC Microprocessor Product Specification
PC7410VGU400L 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:PowerPC 7410 RISC Microprocessor Product Specification
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*