- 您現在的位置：買賣IC網 > PDF目錄369948 > PC28F640J3A-150 (Intel Corp.) Intel StrataFlash Memory (J3) PDF資料下載
參數資料
| 型號： | PC28F640J3A-150 |
| 廠商： | Intel Corp. |
| 英文描述： | Intel StrataFlash Memory (J3) |
| 中文描述： | 英特爾StrataFlash存儲器（J3） |
| 文件頁數： | 37/72頁 |
| 文件大?。?/td> | 905K |
| 代理商： | PC28F640J3A-150 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
256-Mbit J3 (x8/x16)
Datasheet
37
10.0
Read Operations
The device supports four types of read modes: Read Array, Read Identifier, Read Status, and CFI
query. Upon power-up or return from reset, the device defaults to read array mode. To change the
device’s read mode, the appropriate read-mode command must be written to the device. (See
Section 9.2, “Device Commands” on page 35
.) See
Section 14.0, “Special Modes” on page 50
for
details regarding read status, read ID, and CFI query modes.
Upon initial device power-up or after exit from reset/power-down mode, the device automatically
resets to read array mode. Otherwise, write the appropriate read mode command (Read Array, Read
Query, Read Identifier Codes, or Read Status Register) to the CUI. Six control signals dictate the
data flow in and out of the component: CE0, CE1, CE2, OE#, WE#, and RP#. The device must be
enabled (see
Table 13, “Chip Enable Truth Table” on page 33
), and OE# must be driven active to
obtain data at the outputs. CE0, CE1, and CE2 are the device selection controls and, when enabled
(see
Table 13
), select the memory device. OE# is the data output (D[15:0]) control and, when
active, drives the selected memory data onto the I/O bus. WE# must be at V
IH
.
10.1
Read Array
Upon initial device power-up and after exit from reset/power-down mode, the device defaults to
read array mode. The device defaults to four-word asynchronous read page mode. The Read Array
command also causes the device to enter read array mode. The device remains enabled for reads
until another command is written. If the internal WSM has started a block erase, program, or lock-
bit configuration, the device will not recognize the Read Array command until the WSM completes
its operation unless the WSM is suspended via an Erase or Program Suspend command. The Read
Array command functions independently of the V
PEN
voltage.
10.1.1
Asynchronous Page Mode Read
There are two Asynchronous Page mode configurations that are available depending on the user’s
system design requirements:
Four-Word Page mode: This is the default mode on power-up or reset. Array data can be
sensed up to four words (8 Bytes) at a time.
Eight-Word Page mode: Array data can be sensed up to eight words (16 Bytes) at a time. This
mode must be enabled on power-up or reset by using the command sequence found in
Table 14, “Command Bus-Cycle Definitions” on page 35
. Address bits A[3:1] determine
which word is output during a read operation, and A[3:0] determine which byte is output for a
x8 bus width.
After the initial access delay, the first word out of the page buffer corresponds to the initial address.
In Four-Word Page mode, address bits A[2:1] determine which word is output from the page buffer
for a x16 bus width, and A[2:0] determine which byte is output from the page buffer for a x8 bus
width. Subsequent reads from the device come from the page buffer. These reads are output on
D[15:0] for a x16 bus width and D[7:0] for a x8 bus width after a minimum delay as long as A[2:0]
(Four-Word Page mode) or A[3:0] (Eight-Word Page mode) are the only address bits that change.
Data can be read from the page buffer multiple times, and in any order. In Four-Word Page Mode,
if address bits A[MAX:3] (A[MAX:4] for Eight-Word Page Mode) change at any time, or if CE# is
toggled, the device will sense and load new data into the page buffer. Asynchronous Page Mode is
the default read mode on power-up or reset.
相關PDF資料 |
PDF描述 |
|---|---|
| PC28F640J3C-120 | Intel StrataFlash Memory (J3) |
| PC28F256J3C-115 | Intel StrataFlash Memory (J3) |
| PC28F128J3C-115 | Intel StrataFlash Memory (J3) |
| PC28F640J3C-115 | Intel StrataFlash Memory (J3) |
| PC28F320J3C-115 | Intel StrataFlash Memory (J3) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PC28F640J3C-110 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel StrataFlash Memory (J3) |
| PC28F640J3C115 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| PC28F640J3C-115 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel StrataFlash Memory (J3) |
| PC28F640J3C120 | 制造商:Intel 功能描述: |
| PC28F640J3C-120 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Intel StrataFlash Memory (J3) |
發布緊急采購，3分鐘左右您將得到回復。