- 您現在的位置：買賣IC網 > PDF目錄367756 > PAK-II (Electronic Theatre Controls, Inc.) 310 Ivy Glen Court PDF資料下載
參數資料
| 型號： | PAK-II |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 310 Ivy Glen Court |
| 中文描述： | 310常春藤格倫法院 |
| 文件頁數： | 11/28頁 |
| 文件大?。?/td> | 155K |
| 代理商： | PAK-II |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
is a simple matter to tie these lines together since
SOUT is open collector.
Therefore, the minimum number of lines you need
are two. An output for the clock and an I/O line to
connect to SIN and SOUT. You'll connect the
Enable/Busy pin to +5V and use a pull up resistor
to 5V on the Busy/Mode pin. This allows you to
reset the device and communicate with it. The only
problem is, you will have to make sure not to ask
the device for data while it is processing. Most
operations are quite fast, but some operations
(calculating digits and division, for example) can
take as much as 200uS with the provided
components.
For some applications, this isn't a problem. For
example, a standard Basic Stamp II can't operate
fast enough for this to be a problem except for
division and digit calculations. However, you may
want to know when the device is ready to process.
There are two ways you can accomplish this.
If you need to disable and enable the device, you'll
want to drive the Enable/Busy pin. Using this pin
allows you to share the SIN, SOUT, and CLK
lines with other devices that use a similar protocol.
So to connect 5 Paks you'd only need 7 I/O lines (5
enables, 1 SIN/SOUT, and 1 CLK line). You drive
the Enable/Busy pin low to disable the device. If
you don't plan to use this capability, just pull the
pin high with a pull up resistor. If you are using
the Busy/Mode input (see below) you can still use
相關PDF資料 |
PDF描述 |
|---|---|
| PAK-IV | Using the PAK-IV I/O Coprocessor |
| PAK-I | 310 Ivy Glen Court |
| PAK-VA | 310 Ivy Glen Court |
| PAK-VI | 310 Ivy Glen Court |
| PAL10016P8 | 3ns ECL ASPECT Programmable Array Logic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PAK-III | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Using the PAK-III I/O Coprocessor |
| PAK-IV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Using the PAK-IV I/O Coprocessor |
| PAKKL-3140-01 | 制造商:Richco 功能描述:CLIP ADJ SNAP IN NAT .31-.40" |
| PAKKL-3140-19 | 功能描述:CLIP ADJ. SNAP .31-.40" RoHS:是 類別:線纜，導線 - 管理 >> 線夾和夾具 系列:KWIK KLIP 標準包裝:100 系列:TC 類型:C-夾 開口尺寸:0.79" L x 0.54" W x 0.67" H（20.1mm x 13.7mm x 17.0mm） 安裝類型:釘子 材質:聚丙烯 顏色:黑 |
| PAKKL-4756-01 | 制造商:Richco 功能描述:CLIP ADJ SNAP IN NAT .47-.56" |
發布緊急采購，3分鐘左右您將得到回復。