參數資料
型號： P89LPC9401FBD,557
廠商： NXP Semiconductors
文件頁數： 36/59頁
文件大?。?/td> 0K
描述： IC 80C51 MCU FLASH 8K 64-LQFP
標準包裝： 450
系列： LPC900
核心處理器： 8051
芯體尺寸： 8-位
速度： 18MHz
連通性： I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，LCD，LED，POR，PWM，WDT
輸入/輸出數： 23
程序存儲器容量： 8KB（8K x 8）
程序存儲器類型： 閃存
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.4 V ~ 3.6 V
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 64-LQFP
包裝： 托盤
其它名稱： 935278626557
P89LPC9401_1
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 — 5 September 2005
41 of 59
Philips Semiconductors
P89LPC9401
8-bit two-clock 80C51 microcontroller with 32 segment
× 4 LCD driver
7.27.5 Flash programming and erasing
Four different methods of erasing or programming of the ash are available. The ash may
be programmed or erased in the end-user application (IAP) under control of the
application’s rmware. Another option is to use the ICP mechanism. This ICP system
provides for programming through a serial clock - serial data interface. As shipped from
the factory, the upper 512 bytes of user code space contains a serial ISP routine allowing
for the device to be programmed in circuit through the serial port. The ash may also be
programmed or erased using a commercially available EPROM programmer which
supports this device. This device does not provide for direct verication of code memory
contents. Instead, this device provides a 32-bit CRC result on either a sector or the entire
user code space.
7.27.6 In-circuit programming
ICP is performed without removing the microcontroller from the system. The ICP facility
consists of internal hardware resources to facilitate remote programming of the
P89LPC9401 through a two-wire serial interface. The Philips ICP facility has made ICP in
an embedded application—using commercially available programmers—possible with a
minimum of additional expense in components and circuit board area. The ICP function
uses ve pins. Only a small connector needs to be available to interface your application
to a commercial programmer in order to use this feature. Additional details may be found
in the
P89LPC9401 User manual.
7.27.7 In-application programming
IAP is performed in the application under the control of the microcontroller’s rmware. The
IAP facility consists of internal hardware resources to facilitate programming and erasing.
The Philips IAP has made IAP in an embedded application possible without additional
components. Two methods are available to accomplish IAP. A set of predened IAP
functions are provided in a Boot ROM and can be called through a common interface,
PGM_MTP. Several IAP calls are available for use by an application program to permit
selective erasing and programming of ash sectors, pages, security bits, conguration
bytes, and device ID. These functions are selected by setting up the microcontroller’s
registers before making a call to PGM_MTP at FF03H. The Boot ROM occupies the
program memory space at the top of the address space from FF00 to FEFFH, thereby not
conicting with the user program memory space.
In addition, IAP operations can be accomplished through the use of four SFRs consisting
of a control/status register, a data register, and two address registers. Additional details
may be found in the
P89LPC9401 User manual.
7.27.8 In-system programming
ISP is performed without removing the microcontroller from the system. The ISP facility
consists of a series of internal hardware resources coupled with internal rmware to
facilitate remote programming of the P89LPC9401 through the serial port. This rmware is
provided by Philips and embedded within each P89LPC9401 device. The Philips ISP
facility has made ISP in an embedded application possible with a minimum of additional
expense in components and circuit board area. The ISP function uses ve pins (VDD,VSS,
TXD, RXD, and RST). Only a small connector needs to be available to interface your
application to an external circuit in order to use this feature.
相關PDF資料
PDF描述
P89LPC9402FBD,557 IC 80C51 MCU FLASH 8K 64-LQFP
P89LPC954FBD44,151 IC 80C51 MCU FLASH 16K 44LQFP
P89LPC972FN,129 MCU 80C51 8KB FLASH 20DIP
P89LPC985FDH,529 IC 80C51 MCU KB FLASH 28TSSOP
P89V51RC2FA,512 IC 80C51 MCU FLASH 32K 44-PLCC
相關代理商/技術參數
參數描述
P89LPC9402 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 32 segment 4 LCD driver
P89LPC9402FBD 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 32 segment 4 LCD driver
P89LPC9402FBD,557 功能描述:8位微控制器 -MCU IC 80C51 MCU FLASH 8K RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC9408 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with two-clock 80C51 core 8 kB 3 V byte-erasable flash, 32 segment x 4 LCD driver, 10-bit ADC
P89LPC9408FBD 功能描述:8位微控制器 -MCU 8K FL/10B ADC LCD DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*