- 您現在的位置：買賣IC網 > PDF目錄1959 > P89LPC938FDH,529 (NXP Semiconductors)IC 80C51 MCU FLASH 8K 28-TSSOP PDF資料下載
參數資料
| 型號： | P89LPC938FDH,529 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 64/68頁 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU FLASH 8K 28-TSSOP |
| 產品培訓模塊： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 標準包裝： | 51 |
| 系列： | LPC900 |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 18MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，LED，POR，PWM，WDT |
| 輸入/輸出數： | 26 |
| 程序存儲器容量： | 8KB（8K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 512 x 8 |
| RAM 容量： | 768 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 包裝： | 管件 |
| 產品目錄頁面： | 706 (CN2011-ZH PDF) |
| 配用： | 622-1014-ND - BOARD FOR LPC9XX TSSOP 622-1011-ND - BOARD FOR LPC938 TSSOP 622-1008-ND - BOARD FOR LPC9103 10-HVSON 622-1006-ND - SOCKET ADAPTER BOARD 568-4000-ND - DEMO BOARD SPI/I2C TO DUAL UART 568-3510-ND - DEMO BOARD SPI/I2C TO UART 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X 568-1758-ND - BOARD EVAL FOR LPC93X MCU FAMILY |
| 其它名稱： | 568-2013-5 935278546529 P89LPC938FDH-S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁
2010 Microchip Technology Inc.
DS39933D-page 67
PIC18F87J90 FAMILY
6.1.3
PROGRAM COUNTER
The Program Counter (PC) specifies the address of the
instruction to fetch for execution. The PC is 21 bits wide
and is contained in three separate 8-bit registers. The
low byte, known as the PCL register, is both readable
and writable. The high byte, or PCH register, contains
the PC<15:8> bits; it is not directly readable or writable.
Updates to the PCH register are performed through the
PCLATH register. The upper byte is called PCU. This
register contains the PC<20:16> bits; it is also not
directly readable or writable. Updates to the PCU
register are performed through the PCLATU register.
The contents of PCLATH and PCLATU are transferred
to the program counter by any operation that writes
PCL. Similarly, the upper two bytes of the program
counter are transferred to PCLATH and PCLATU by an
operation that reads PCL. This is useful for computed
offsets to the PC (see Section 6.1.6.1 “Computed
The PC addresses bytes in the program memory. To
prevent the PC from becoming misaligned with word
instructions, the Least Significant bit of PCL is fixed to
a value of ‘0’. The PC increments by 2 to address
sequential instructions in the program memory.
The CALL, RCALL, GOTO and program branch
instructions write to the program counter directly. For
these instructions, the contents of PCLATH and
PCLATU are not transferred to the program counter.
6.1.4
RETURN ADDRESS STACK
The return address stack allows any combination of up
to 31 program calls and interrupts to occur. The PC is
pushed onto the stack when a CALL or RCALL instruc-
tion is executed, or an interrupt is Acknowledged. The
PC value is pulled off the stack on a RETURN, RETLW or
a RETFIE instruction (and on ADDULNK and SUBULNK
instructions if the extended instruction set is enabled).
PCLATU and PCLATH are not affected by any of the
RETURN
or CALL instructions.
The stack operates as a 31-word by 21-bit RAM and a
5-bit Stack Pointer, STKPTR. The stack space is not
part of either program or data space. The Stack Pointer
is readable and writable, and the address on the top of
the stack is readable and writable through the
Top-of-Stack Special Function Registers. Data can also
be pushed to, or popped from, the stack, using these
registers.
A CALL type instruction causes a push onto the stack.
The Stack Pointer is first incremented and the location
pointed to by the Stack Pointer is written with the
contents of the PC (already pointing to the instruction
following the CALL). A RETURN type instruction causes
a pop from the stack. The contents of the location
pointed to by the STKPTR are transferred to the PC
and then the Stack Pointer is decremented.
The Stack Pointer is initialized to ‘00000’ after all
Resets. There is no RAM associated with the location
corresponding to a Stack Pointer value of ‘00000’; this
is only a Reset value. Status bits indicate if the stack is
full, has overflowed or has underflowed.
6.1.4.1
Top-of-Stack Access
Only the top of the return address stack (TOS) is
readable and writable. A set of three registers,
TOSU:TOSH:TOSL, holds the contents of the stack
location pointed to by the STKPTR register (Figure 6-3).
This allows users to implement a software stack, if nec-
essary. After a CALL, RCALL or interrupt (and ADDULNK
and SUBULNK instructions if the extended instruction set
is enabled), the software can read the pushed value by
reading the TOSU:TOSH:TOSL registers. These values
can be placed on a user-defined software stack. At
return time, the software can return these values to
TOSU:TOSH:TOSL and do a return.
The user must disable the global interrupt enable bits
while accessing the stack to prevent inadvertent stack
corruption.
FIGURE 6-3:
RETURN ADDRESS STACK AND ASSOCIATED REGISTERS
00011
001A34h
11111
11110
11101
00010
00001
00000
00010
Return Address Stack <20:0>
Top-of-Stack
000D58h
TOSL
TOSH
TOSU
34h
1Ah
00h
STKPTR<4:0>
Top-of-Stack Registers
Stack Pointer
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC9401FBD,557 | IC 80C51 MCU FLASH 8K 64-LQFP |
| P89LPC9402FBD,557 | IC 80C51 MCU FLASH 8K 64-LQFP |
| P89LPC954FBD44,151 | IC 80C51 MCU FLASH 16K 44LQFP |
| P89LPC972FN,129 | MCU 80C51 8KB FLASH 20DIP |
| P89LPC985FDH,529 | IC 80C51 MCU KB FLASH 28TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC938FHN | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A/D converter |
| P89LPC938FHN,151 | 功能描述:8位微控制器 -MCU 8K FL/768B RAM/512B RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC938FHN-S | 功能描述:8位微控制器 -MCU 8K FL/768B RAM/512B EE/10B ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC9401 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 32 segment x 4 LCD driver |
| P89LPC9401FBD | 制造商:NXP Semiconductors 功能描述:IC MCU 8BIT 80C51 LCD DRIVER SMD 制造商:NXP Semiconductors 功能描述:IC, MCU 8BIT 80C51, LCD DRIVER, SMD |
發布緊急采購，3分鐘左右您將得到回復。