- 您現在的位置：買賣IC網 > PDF目錄367742 > P89LPC936 (NXP Semiconductors N.V.) 8-BIT SINGLE CHIP MICROCONTROLLERS PDF資料下載
參數資料
| 型號： | P89LPC936 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT SINGLE CHIP MICROCONTROLLERS |
| 中文描述： | 8位單晶片微控制器 |
| 文件頁數： | 32/75頁 |
| 文件大?。?/td> | 372K |
| 代理商： | P89LPC936 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁
9397 750 15113
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 06 — 20 June 2005
32 of 75
Philips Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
8.14.1
Brownout detection
The brownout detect function determines if the power supply voltage drops below a
certain level. The default operation is for a brownout detection to cause a processor reset,
however it may alternatively be configured to generate an interrupt.
Brownout detection may be enabled or disabled in software.
If brownout detection is enabled the brownout condition occurs when V
DD
falls below the
brownout trip voltage, V
bo
(see
Table 11 “Static characteristics”
), and is negated when V
DD
rises above V
bo
. If the P89LPC933/934/935/936 device is to operate with a power supply
that can be below 2.7 V, BOE should be left in the unprogrammed state so that the device
can operate at 2.4 V, otherwise continuous brownout reset may prevent the device from
operating.
For correct activation of brownout detect, the V
DD
rise and fall times must be observed.
Please see
Table 11 “Static characteristics”
for specifications.
8.14.2
Power-on detection
The power-on detect has a function similar to the brownout detect, but is designed to work
as power comes up initially, before the power supply voltage reaches a level where
brownout detect can work. The POF flag in the RSTSRC register is set to indicate an
initial power-up condition. The POF flag will remain set until cleared by software.
8.15 Power reduction modes
The P89LPC933/934/935/936 supports three different power reduction modes. These
modes are Idle mode, Power-down mode, and total Power-down mode.
8.15.1
Idle mode
Idle mode leaves peripherals running in order to allow them to activate the processor
when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle
mode.
8.15.2
Power-down mode
The Power-down mode stops the oscillator in order to minimize power consumption. The
P89LPC933/934/935/936 exits Power-down mode via any reset, or certain interrupts. In
Power-down mode, the power supply voltage may be reduced to the RAM keep-alive
voltage V
RAM
. This retains the RAM contents at the point where Power-down mode was
entered. SFR contents are not guaranteed after V
DD
has been lowered to V
RAM
, therefore
it is highly recommended to wake-up the processor via reset in this case. V
DD
must be
raised to within the operating range before the Power-down mode is exited.
Some chip functions continue to operate and draw power during Power-down mode,
increasing the total power used during power-down. These include: brownout detect,
watchdog timer, Comparators (note that Comparators can be powered-down separately),
and RTC/system timer. The internal RC oscillator is disabled unless both the RC oscillator
has been selected as the system clock and the RTC is enabled.
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC938 | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A/D converter |
| P89LPC938FA | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A/D converter |
| P89LV51RB2BBC | 8-bit 80C51 3 V low power 16/32/64 kB Flash microcontroller with 1 kB RAM |
| P89LV51RB2 | 8-bit 80C51 3 V low power 16/32/64 kB Flash microcontroller with 1 kB RAM |
| P89LV51RB2BA | 8-bit 80C51 3 V low power 16/32/64 kB Flash microcontroller with 1 kB RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC9361FDH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core, 4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs |
| P89LPC9361FDH,518 | 功能描述:8位微控制器 -MCU MCU 8-Bit 80C51 8KB Flash 2.5V/3.3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC936FA | 制造商:NXP Semiconductors 功能描述: 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 16K FLASH PLCC28 |
| P89LPC936FA,529 | 功能描述:8位微控制器 -MCU 80C51 16K FL 768B RM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC936FA529 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ LCC-28 |
發布緊急采購，3分鐘左右您將得到回復。