- 您現在的位置：買賣IC網 > PDF目錄367742 > P89LPC934 (NXP Semiconductors N.V.) 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB 3 V byte-erasable Flash with 8-bit A/D converters PDF資料下載
參數資料
| 型號： | P89LPC934 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 串行ADC |
| 英文描述： | 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB 3 V byte-erasable Flash with 8-bit A/D converters |
| 中文描述： | 8位加速兩個微控制器80C51的時鐘4 KB的核心/ 8 KB的3伏字節可擦除閃存的8位A / D轉換器 |
| 文件頁數： | 55/75頁 |
| 文件大?。?/td> | 372K |
| 代理商： | P89LPC934 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁當前第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁
9397 750 15113
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 06 — 20 June 2005
55 of 75
Philips Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
9.5.3
Edge triggered
An A/D conversion is started by rising or falling edge of P1.4. Once a conversion has
started, additional edge triggers are ignored until the conversion has completed. The edge
triggered start mode is available in all A/D operating modes.
9.5.4
Dual start immediately (P89LPC935/936)
Programming this mode starts a synchronized conversion of both A/D converters.This
start mode is available in all A/D operating modes. Both A/D converters must be in the
same operating mode. In the continuous conversion modes, both A/D converters must
select an identical number of channels. Any trigger of either A/D will start a simultaneous
conversion of both A/Ds.
9.6 Boundary limits interrupt
Each of the A/D converters has both a high and low boundary limit register. After the four
MSBs have been converted, these four bits are compared with the four MSBs of the
boundary high and low registers. If the four MSBs of the conversion are outside the limit
an interrupt will be generated, if enabled. If the conversion result is within the limits, the
boundary limits will again be compared after all 8 bits have been converted. An interrupt
will be generated, if enabled, if the result is outside the boundary limits. The boundary limit
may be disabled by clearing the boundary limit interrupt enable.
9.7 DAC output to a port pin with high output impedance
Each A/D converter’s DAC block can be output to a port pin. In this mode, the ADxDAT3
register is used to hold the value fed to the DAC. After a value has been written to the DAC
(written to ADxDAT3), the DAC output will appear on the channel 3 pin.
9.8 Clock divider
The A/D converter requires that its internal clock source be in the range of 500 kHz to
3.3 MHz to maintain accuracy. A programmable clock divider that divides the clock
from 1 to 8 is provided for this purpose.
9.9 Power-down and Idle mode
In Idle mode the A/C converter, if enabled, will continue to function and can cause the
device to exit Idle mode when the conversion is completed if the A/D interrupt is enabled.
In Power-down mode or Total Power-down mode, the A/D does not function. If the A/D is
enabled, it will consume power. Power can be reduced by disabling the A/D.
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC935 | 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB 3 V byte-erasable Flash with 8-bit A/D converters |
| P89LPC935FA | 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB 3 V byte-erasable Flash with 8-bit A/D converters |
| P89LPC936 | 8-BIT SINGLE CHIP MICROCONTROLLERS |
| P89LPC938 | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A/D converter |
| P89LPC938FA | 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A/D converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC9341FDH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core, 4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs |
| P89LPC9341FDH,512 | 功能描述:8位微控制器 -MCU IC 80C51 MCU FLASH 8K RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC934FDH | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 8K FLASH TSSOP28 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 8K FLASH, TSSOP28, Controller Family/Series:(8051) 8052, Core Siz |
| P89LPC934FDH,529 | 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC934FDH-S | 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。