參數資料
型號： P89LPC934
廠商： NXP Semiconductors N.V.
元件分類： 串行ADC
英文描述： 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB 3 V byte-erasable Flash with 8-bit A/D converters
中文描述： 8位加速兩個微控制器80C51的時鐘4 KB的核心/ 8 KB的3伏字節可擦除閃存的8位A / D轉換器
文件頁數： 50/75頁
文件大?。?/td> 372K
代理商： P89LPC934
9397 750 15113
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 06 — 20 June 2005
50 of 75
Philips Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
8.28.3
Flash organization
The program memory consists of eight 2 kB sectors on the P89LPC936 device, eight 1 kB
sectors on the P89LPC934/935 devices, and four 1 kB sectors on the P89LPC933 device.
Each sector can be further divided into 64-byte pages. In addition to sector erase, page
erase, and byte erase, a 64-byte page register is included which allows from 1 to 64 bytes
of a given page to be programmed at the same time, substantially reducing overall
programming time.
8.28.4
Using flash as data storage
The flash code memory array of this device supports individual byte erasing and
programming. Any byte in the code memory array may be read using the MOVC
instruction, provided that the sector containing the byte has not been secured (a MOVC
instruction is not allowed to read code memory contents of a secured sector). Thus any
byte in a non-secured sector may be used for non-volatile data storage.
8.28.5
Flash programming and erasing
Four different methods of erasing or programming of the flash are available. The flash may
be programmed or erased in the end-user application (IAP) under control of the
application’s firmware. Another option is to use the ICP mechanism. This ICP system
provides for programming through a serial clock - serial data interface. As shipped from
the factory, the upper 512 bytes of user code space contains a serial ISP routine allowing
the device to be programmed in circuit through the serial port. The flash may also be
programmed or erased using a commercially available EPROM programmer which
supports this device. This device does not provide for direct verification of code memory
contents. Instead, this device provides a 32-bit CRC result on either a sector or the entire
user code space.
8.28.6
In-circuit programming
ICP is performed without removing the microcontroller from the system. The ICP facility
consists of internal hardware resources to facilitate remote programming of the
P89LPC933/934/935/936 through a two-wire serial interface. The Philips ICP facility has
made ICP in an embedded application—using commercially available
programmers—possible with a minimum of additional expense in components and circuit
board area. The ICP function uses five pins. Only a small connector needs to be available
to interface your application to a commercial programmer in order to use this feature.
Additional details may be found in the P89LPC933/934/935/936 User manual
8.28.7
In-application programming
IAP is performed in the application under the control of the microcontroller’s firmware. The
IAP facility consists of internal hardware resources to facilitate programming and erasing.
The Philips IAP has made IAP in an embedded application possible without additional
components. Two methods are available to accomplish IAP. A set of predefined IAP
functions are provided in a boot ROM and can be called through a common interface,
PGM_MTP. Several IAP calls are available for use by an application program to permit
selective erasing and programming of flash sectors, pages, security bits, configuration
bytes, and device ID. These functions are selected by setting up the microcontroller’s
registers before making a call to PGM_MTP at FF03H. The boot ROM occupies the
program memory space at the top of the address space from FF00H to FFEFH, thereby
not conflicting with the user program memory space.
相關PDF資料
PDF描述
P89LPC935 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB 3 V byte-erasable Flash with 8-bit A/D converters
P89LPC935FA 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB 3 V byte-erasable Flash with 8-bit A/D converters
P89LPC936 8-BIT SINGLE CHIP MICROCONTROLLERS
P89LPC938 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A/D converter
P89LPC938FA 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable Flash with 10-bit A/D converter
相關代理商/技術參數
參數描述
P89LPC9341FDH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core, 4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs
P89LPC9341FDH,512 功能描述:8位微控制器 -MCU IC 80C51 MCU FLASH 8K RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC934FDH 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 8K FLASH TSSOP28 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 8K FLASH, TSSOP28, Controller Family/Series:(8051) 8052, Core Siz
P89LPC934FDH,529 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC934FDH-S 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*