- 您現在的位置：買賣IC網 > PDF目錄367742 > P89LPC913 (NXP Semiconductors N.V.) 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM PDF資料下載
參數資料
| 型號： | P89LPC913 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| 中文描述： | 8位微控制器兩個小時80C51的核心具有1KB 3伏閃光的128字節RAM |
| 文件頁數： | 35/63頁 |
| 文件大?。?/td> | 314K |
| 代理商： | P89LPC913 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
Philips Semiconductors
P89LPC912/913/914
8-bit microcontrollers with two-clock 80C51 core
Product data
Rev. 03 — 17 December 2004
35 of 63
9397 750 14468
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9.13.1
Idle mode
Idle mode leaves peripherals running in order to allow them to activate the processor
when an interrupt is generated. Any enabled interrupt source or reset may terminate
Idle mode.
9.13.2
Power-down mode
The Power-down mode stops the oscillator in order to minimize power consumption.
The P89LPC912/913/914 exits Power-down mode via any reset, or certain interrupts.
In Power-down mode, the power supply voltage may be reduced to the RAM
keep-alive voltage V
RAM
. This retains the RAM contents at the point where
Power-down mode was entered. SFR contents are not guaranteed after V
DD
has
been lowered to V
RAM
, therefore it is highly recommended to wake up the processor
via reset in this case. V
DD
must be raised to within the operating range before the
Power-down mode is exited.
Some chip functions continue to operate and draw power during Power-down mode,
increasing the total power used during Power-down. These include: Brownout detect,
Watchdog Timer, Comparators (note that Comparators can be powered-down
separately), and Real-Time Clock (RTC)/System Timer. The internal RC oscillator is
disabled unless both the RC oscillator has been selected as the system clock
and
the
RTC is enabled.
9.13.3
Total Power-down mode
This is the same as Power-down mode except that the brownout detection circuitry
and the voltage comparators are also disabled to conserve additional power. The
internal RC oscillator is disabled unless both the RC oscillator has been selected as
the system clock
and
the RTC is enabled. If the internal RC oscillator is used to clock
the RTC during Power-down, there will be high power consumption. Please use an
external low frequency clock to achieve low power with the Real-Time Clock running
during Power-down.
9.14 Reset
The P1.5/RST pin can function as either an active-LOW reset input or as a digital
input, P1.5. The RPE (Reset Pin Enable) bit in UCFG1, when set to ‘1’, enables the
external reset input function on P1.5. When cleared, P1.5 may be used as an input
pin.
Remark:
During a power-up sequence, the RPE selection is overridden and this pin
will always function as a reset input.
An external circuit connected to this pin
should not hold this pin LOW during a power-on sequence as this will keep the
device in reset.
After power-up this input will function either as an external reset
input or as a digital input as defined by the RPE bit. Only a power-up reset will
temporarily override the selection defined by RPE bit. Other sources of reset will not
override the RPE bit.
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC914 | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| P89LPC914FDH | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| P89LPC924 | 8-bit microcontrollers with accelerated two-clock 80C51 core 4 kB/8 kB 3 V low-power Flash with 8-bit A/D converter |
| P89LPC925 | 8-bit microcontrollers with accelerated two-clock 80C51 core 4 kB/8 kB 3 V low-power Flash with 8-bit A/D converter |
| P89LPC930 | 8-bit microcontrollers with two-clock 80C51 core 4 kB/8 kB 3 V Flash with 256-byte data RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC913FDH | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 1K FLASH TSSOP14 |
| P89LPC913FDH,129 | 功能描述:8位微控制器 -MCU 1K FL/128B RAM/SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC913FDH129 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| P89LPC913FDH-S | 功能描述:8位微控制器 -MCU 1K FL/128B RAM/SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC914 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
發布緊急采購，3分鐘左右您將得到回復。