參數資料
型號: P89LPC902FD
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
中文描述: 8-BIT, FLASH, 7.3728 MHz, MICROCONTROLLER, PDSO8
封裝: 3.90 MM, PLASTIC, MS-012, SOT-96-1, SO-8
文件頁數: 11/55頁
文件大?。?/td> 1236K
代理商: P89LPC902FD
Philips Semiconductors
P89LPC901/902/903
8-bit microcontrollers with two-clock 80C51 core
Product data
Rev. 04 — 21 November 2003
11 of 55
9397 750 12293
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
Table 5:
Symbol
P0.0 - P0.6
P89LPC903 pin description
Pin
2, 6, 7
Type
I/O
Description
Port 0:
Port 0 is an I/O port with a user-configurable output type. During reset Port 0
latches are configured in the input only mode with the internal pull-up disabled. The
operation of Port 0 pins as inputs and outputs depends upon the port configuration
selected. Each port pin is configured independently. Refer to
Section 8.12.1 “Port
configurations”
and
Table 13 “DC electrical characteristics”
for details.
The Keypad Interrupt feature operates with Port 0 pins.
All pins have Schmitt triggered inputs.
Port 0 also provides various special functions as described below:
P0.2 —
Port 0 bit 2.
CIN2A —
Comparator 2 positive input.
KBI2 —
Keyboard input 2.
P0.4 —
Port 0 bit 4.
CIN1A —
Comparator 1 positive input.
KBI4 —
Keyboard input 4.
P0.5 —
Port 0 bit 5.
CMPREF —
Comparator reference (negative) input.
KBI5 —
Keyboard input 5.
Port 1:
Port 1 is an I/O port with a user-configurable output type. During reset Port 1
latches are configured in the input only mode with the internal pull-up disabled. The
operation of the configurable Port 1 pins as inputs and outputs depends upon the
port configuration selected. Each of the configurable port pins are programmed
independently. Refer to
Section 8.12.1 “Port configurations”
and
Table 13 “DC
electrical characteristics”
for details. P1.5 is input only.
All pins have Schmitt triggered inputs.
Port 1 also provides various special functions as described below:
P1.0 —
Port 1 bit 0.
TxD —
Serial port transmitter data.
P1.1 —
Port 1 bit 1.
RxD —
Serial port receiver data.
P1.5 —
Port 1 bit 5 (input only).
RST —
External Reset input during Power-on or if selected via UCFG1. When
functioning as a reset input a LOW on this pin resets the microcontroller, causing I/O
ports and peripherals to take on their default states, and the processor begins
execution at address 0. Also used during a power-on sequence to force In-System
Programming mode.
Ground:
0 V reference.
Power Supply:
This is the power supply voltage for normal operation as well as Idle
and Power-down modes.
2
I/O
I
I
I/O
I
I
I/O
I
I
7
6
P1.0 - P1.5
3, 4, 5
5
I/O
O
I/O
I
I
I
3
4
V
SS
V
DD
8
1
I
I
相關PDF資料
PDF描述
P89LPC902FN 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC903 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC903FD 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC907FD 71-331814-05S
P89LPC906 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
相關代理商/技術參數
參數描述
P89LPC902FD,112 功能描述:8位微控制器 -MCU 80C51 1K FL 128B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC902FD.512 制造商:NXP Semiconductors 功能描述:8BIT MCU 1K FLASH 89LC902 SOIC8
P89LPC902FD112 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 12MHZ SOIC-8
P89LPC902FN 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC902FN,129 功能描述:8位微控制器 -MCU 80C51 1K FL 128B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT