參數資料
型號： P80CE559EBB
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： Single-chip 8-bit microcontroller
中文描述： 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80
文件頁數： 9/72頁
文件大?。?/td> 524K
代理商： P80CE559EBB
Philips Semiconductors
Preliminary specification
P83CE559/P80CE559
Single-chip 8-bit microcontroller
1996 Aug 06
9
6.2
The central processing unit (CPU) manipulates operands in three
memory spaces; these are the 64 Kbytes external data memory,
1536 bytes internal data memory (consisting of 256 bytes standard
RAM and 1280 bytes AUX–RAM) and the 48 Kbytes internal and/or
64 Kbytes external program memory (see Figure 4).
Memory Organization
6.2.1
The program memory of the P8xCE559 consists of 48 Kbytes ROM
respectively FEEPROM (”Flash Memory”) on–chip, externally
expandable up to 64 Kbytes. If, during RESET, the EA pin was held
HIGH, the P8xCE559 executes out of the internal program memory
unless the address exceeds 0BFFFH. Locations 0C000H through
0FFFFH are then fetched from the external program memory. If the
EA pin was held LOW during RESET the P8xCE559 fetches all
instructions from the external program memory. The EA input is
latched during RESET and is don’t care after RESET.
Program Memory
The internal program memory content is protected, by setting a
mask programmable security bit (ROM) or by the software
programmable security byte (FEEPROM) respectively, i.e., it cannot
be read out at any time by any test mode or by any instruction in the
external program memory space. The MOVC instructions are the
only ones which have access to program code in the internal or
external program memory. The EA input is latched during RESET
and is ‘don’t care’ after RESET. This implementation prevents from
reading internal program code by switching from external program
memory to internal program memory during MOVC instruction or an
instruction that handles immediate data. Table 1 lists the access to
the internal and external program memory with MOVC instructions
when the security feature has been activated.
6.2.2
The internal data memory is divided into three physically separated
parts:
Internal Data Memory
256 bytes of RAM, 1280 bytes of AUX–RAM, and a 128 bytes
special function area. These can be addressed each in a different
way (see also Table 2).
– RAM 0 to 127 can be addressed directly and indirectly as in the
80C51.
Address pointers are R0 and R1 of the selected registerbank.
– RAM 128 to 255 can only be addressed indirectly.
Address pointers are R0 and R1 of the selected registerbank.
– AUX–RAM 0 to 1279 is also indirectly addressable as external
DATA MEMORY locations 0 to 1279 via MOVX–Datapointer
instruction, unless it is disabled by setting ARD = 1.
AUX–RAM 0 to 1279 is indirectly addressable via pageregister
(XRAMP) and MOVX–Ri instructions, unless it is disabled by
setting ARD = 1 (see Figure 5).
When executing from internal program memory, an access to
AUX–RAM 0 to 1279 will not affect the ports P0, P2, P3.6 and
P3.7.
An access to external DATA MEMORY locations higher than 1279
will be performed with the MOVX @ DPTR instructions in the
same way as in the 80C51 structure, so with P0 and P2 as
data/address bus and P3.6 and P3.7 as write and read timing
signals. Note that the external DATA MEMORY cannot be
accessed with R0 and R1 as address pointer if the AUX–RAM is
enabled (ARD = 0, default).
– The Special Function Registers (SFR) can only be addressed
directly in the address range from 128 to 255 (see Table 5).
– Four register banks, each 8 registers wide, occupy locations 0
through 31 in the lower RAM area. Only one of these banks may
be enabled at a time. The next 16 bytes, locations 32 through 47,
contain 128 directly addressable bit locations.The stack can be
located anywhere in the internal 256 bytes RAM.The stack depth
is only limited by the available internal RAM space of 256 bytes
(see Figure 7).
All registers except the program counter and the four register
banks reside in the Special Function Register address space.
Table 1.
Memory access by the MOVC instruction for protected ROMs
MOVC LOCATION
ACCESS TO INTERNAL
PROGRAM MEMORY
ACCESS TO EXTERNAL
PROGRAM MEMORY
MOVC in internal program memory
YES
YES
MOVC in external program memory
NOTE:
1. If the security feature has not been activated, there are no restrictions for MOVC instructions
.
NO
YES
Table 2.
Internal data memory map
LOCATION
ADDRESSED
RAM
0 to 127
Direct and indirect
AUX–RAM
0 to 1279
Indirect only with MOVX
RAM
128 to 255
Indirect only
SFR
128 to 255
Direct only
相關PDF資料
PDF描述
P80CE559EFB Single-chip 8-bit microcontroller
P83CE598 8-bit microcontroller with on-chip CAN
P8XCE598 8-bit microcontroller with on-chip CAN
P80CE598 8-bit microcontroller with on-chip CAN
P83CL781 Low voltage 8-bit microcontrollers with UART and I2C-bus
相關代理商/技術參數
參數描述
P80CE559EFB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller
P80CE560 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller
P80CE560EFB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller
P80CE562EHA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller
P80CE598 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*