- 您現在的位置：買賣IC網 > PDF目錄367700 > P60ARM-GP1N (Zarlink Semiconductor Inc.) Low power, general purpose 32-bit RISC microprocessor PDF資料下載
參數資料
| 型號： | P60ARM-GP1N |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | Low power, general purpose 32-bit RISC microprocessor |
| 中文描述： | 低功耗，通用32位RISC微處理器 |
| 文件頁數： | 59/120頁 |
| 文件大?。?/td> | 1275K |
| 代理商： | P60ARM-GP1N |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁當前第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
Instruction Set - LDC, STC
55
4.12.2 Addressing modes
ARM60 is responsible for providing the address used by the memory system for the transfer, and the
addressing modes available are a subset of those used in single data transfer instructions. Note, however,
that the immediate offsets are 8 bits wide and specify word offsets for coprocessor data transfers, whereas
they are 12 bits wide and specify byte offsets for single data transfers.
The 8 bit unsigned immediate offset is shifted left 2 bits and either added to (U=1) or subtracted from (U=0)
the base register (Rn); this calculation may be performed either before (P=1) or after (P=0) the base is used
as the transfer address. The modified base value may be overwritten back into the base register (if W=1), or
the old value of the base may be preserved (W=0). Note that post-indexed addressing modes require
explicit setting of the W bit, unlike LDR and STR which always write-back when post-indexed.
The value of the base register, modified by the offset in a pre-indexed instruction, is used as the address for
the transfer of the first word. The second word (if more than one is transferred) will go to or come from an
address one word (4 bytes) higher than the first transfer, and the address will be incremented by one word
for each subsequent transfer.
4.12.3 Address Alignment
The base address should normally be a word aligned quantity. The bottom 2 bits of the address will appear
on
A[1:0]
and might be interpreted by the memory system.
4.12.4 Use of R15
If Rn is R15, the value used will be the address of the instruction plus 8 bytes. Base write-back to R15 shall
not be specified.
4.12.5 Data aborts
If the address is legal but the memory manager generates an abort, the data trap will be taken. The write-
back of the modified base will take place, but all other processor state will be preserved. The coprocessor is
partly responsible for ensuring that the data transfer can be restarted after the cause of the
abort has been
resolved, and must ensure that any subsequent actions it undertakes can be repeated when the instruction
is retried.
The state of the
LATEABT
control signal does not affect the behaviour of LDC and STC instructions in the
event of an
Abort
exception.
4.12.6 Instruction Cycle Times
Coprocessor data transfer instructions take (n-1)S + 2N + bI incremental cycles to execute, where S, N and
I are as defined in section 5.1 Cycle types on page 65.
n
is the number of words transferred.
b
is the number of cycles spent in the coprocessor busy-wait loop.
4.12.7 Assembler syntax
<LDC|STC>{cond}{L} p#,cd,<Address>
相關PDF資料 |
PDF描述 |
|---|---|
| P60ARM-IG | Low power, general purpose 32-bit RISC microprocessor |
| P60ARM-B | Low power, general purpose 32-bit RISC microprocessor |
| P60A | 60W DC-DC Converter P60A-Series |
| P60A12D05P | 60W DC-DC Converter P60A-Series |
| P60A12D12P | 60W DC-DC Converter P60A-Series |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P60ARM-IG | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Low power, general purpose 32-bit RISC microprocessor |
| P-60AS/A18 | 功能描述:BATTERY NICAD 2/3A 600MAH W/TAB RoHS:否 類別:電池產品 >> 電池，充電式（蓄電池） 系列:- MSDS 材料安全數據表:Nickel Metal Hydride Battery MSDS 標準包裝:1,000 系列:TWICELL 電池化學:鎳金屬氫化物 電池大小:AAA 電壓 - 額定:1.2V 容量:930mAh 尺寸/尺寸:- 端接類型:焊片 放電速率:186mA 標準充電電流:100mA 標準充電時間:16小時 重量:0.029 磅（13.15g） 裝運信息:- 其它名稱:SY153T |
| P60AS302 | 制造商:APEM 功能描述: |
| P60AS632-8C | 制造商:NYLOK 功能描述: |
| P60AS701 | 功能描述:旋鈕開關 10POS BCD 0.15A 24V RoHS:否 制造商:C&K Components 位置數量:5 卡片組數量: 每卡片組極數:2 電流額定值:250 mA 電壓額定值:125 V 指數角: 觸點類型: 觸點形式:DPST 端接類型:Solder 安裝類型:Panel 觸點電鍍:Silver |
發布緊急采購，3分鐘左右您將得到回復。