Fusion Family of Mixed Signal FPGAs
Revision 4
3-3
Table 3-2 Recommended Operating Conditions1
Symbol
Parameter2
Commercial
Industrial
Units
TJ
Junction temperature
0 to +85
–40 to +100
°C
VCC
1.5 V DC core supply voltage
1.425 to 1.575
V
VJTAG
JTAG DC voltage
1.4 to 3.6
V
VPUMP
Programming voltage
Programming mode3
3.15 to 3.45
V
Operation4
0 to 3.6
V
VCCPLL
Analog power supply (PLL)
1.425 to 1.575
V
VCCI
1.5 V DC supply voltage
1.425 to 1.575
V
1.8 V DC supply voltage
1.7 to 1.9
V
2.5 V DC supply voltage
2.3 to 2.7
V
3.3 V DC supply voltage
3.0 to 3.6
V
LVDS differential I/O
2.375 to 2.625
V
LVPECL differential I/O
3.0 to 3.6
V
VCC33A
+3.3 V power supply
2.97 to 3.63
V
VCC33PMP +3.3 V power supply
2.97 to 3.63
V
VAREF
Voltage reference for ADC
2.527 to 2.593
V
VCC15A 5
Digital power supply for the analog system
1.425 to 1.575
V
VCCNVM
Embedded flash power supply
1.425 to 1.575
V
VCCOSC
Oscillator power supply
2.97 to 3.63
V
AV, AC 6
Unpowered, ADC reset asserted or unconfigured
–10.5 to 12.0
–10.5 to 11.6
V
Analog input (+16 V to +2 V prescaler range)
–0.3 to 12.0
–0.3 to 11.6
V
Analog input (+1 V to + 0.125 V prescaler range)
–0.3 to 3.6
V
Analog input (–16 V to –2 V prescaler range)
–10.5 to 0.3
V
Analog input (–1 V to –0.125 V prescaler range)
–3.6 to 0.3
V
Analog input (direct input to ADC)
–0.3 to 3.6
V
Digital input
–0.3 to 12.0
–0.3 to 11.6
V
AG 6
Unpowered, ADC reset asserted or unconfigured
–10.5 to 12.0
–10.5 to 11.6
V
Low Current Mode (1 A, 3 A, 10 A, 30 A)
–0.3 to 12.0
–0.3 to 11.6
V
Low Current Mode (–1 A, –3 A, –10 A, –30 A)
–10.5 to 0.3
V
High Current Mode 7
–10.5 to 12.0
–10.5 to 11.6
V
AT 6
Unpowered, ADC reset asserted or unconfigured
–0.3 to 15.5
–0.3 to 14.5
V
Analog input (+16 V, +4 V prescaler range)
–0.3 to 15.5
–0.3 to 14.5
V
Analog input (direct input to ADC)
–0.3 to 3.6
V
Digital input
–0.3 to 15.5
–0.3 to 14.5
V
Notes:
1. The ranges given here are for power supplies only. The recommended input voltage ranges specific to each I/O
2. All parameters representing voltages are measured with respect to GND unless otherwise specified.
3. The programming temperature range supported is Tambient = 0°C to 85°C.
4. VPUMP can be left floating during normal operation (not programming mode).
5. Violating the VCC15A recommended voltage supply during an embedded flash program cycle can corrupt the page being
programmed.
6. The input voltage may overshoot by up to 500 mV above the Recommended Maximum (150 mV in Direct mode),
provided the duration of the overshoot is less than 50% of the operating lifetime of the device.